71606 (ATICSE3) LG Refrigerator - Instructions

Unable to complete repair, had to send parts back
Part should have been PS11732074, but got PS11732704- wrong part
This was a substitute part and was 2" too long

Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!

Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!

Removed upper drawer/basket from freezer

Removed 2 Philips screws

Removed rail bracket assembly

Reinstalled reversing those steps

Works like new.
Happy wife. Happy life. FYI- I am nearly 77 yrs young.

Took out tray , removed 2 screws, removed old rail and installed new one.

Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.

1. Remove all food from the shelf and take out the crisper drawers.
2. Remove the glass and take out the crisper frame.
3. Take the screws out of the frame that are holding the cover frame in place and remove the old cover frame..
4. Install the new cover and replace screws.
5. Re- install the drawers and glass.

( I'm a 76 yr old female and did it myself with the help of the instructions you provided!). Thanks

I disconnected the refrigerator power, removed the 2 screws holding the mullion door on the left side of the refrigerator French-door (it’s the flap that allows the door to close). Removed the broken spring and installed the replacement spring in its place. Reinstalled the mullion door by putting it in place and installing the previously removed screws.

i changed the filter and was able to get water to the white coil at the bottom of the dispenser (left door) but could never get water to the icemalker.i also replaced the pump at the bottom of the door as well as the green ebr699172 dispenser electrical board.still can not get water to the icemaker.any help will be greatly appreciated.
paul

Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)