All Installation Instructions for LG Refrigerator 71059

Unit kept beeping as if the freezer door was open

I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

Parts Used:

Switch,Push Button

Paul from San Jose, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

water supply to ice maker leaked

Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new

Parts Used:

Plastic Tube - 5/16 Inch

john from locust valley, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light out

slid screw driver under edge of switch, easy.

Parts Used:

Refrigerator Door Switch

Jack from Ellenton, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My dishwasher was leaking water

The repair went well. They actually had to replace the motor. This saved me a lot of money having it repaired in this manner. Very professional & pleasant.

Parts Used:

Refrigerator Water Filter

rosalie from wayne, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Spring was broken on original unit, had to replace whole lever.

removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!

Parts Used:

Spring,Lever

Alan from Sun City West, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Blower motor out on condenser

followed detailed movie from Utube video

Parts Used:

Evaporator Fan Motor

George from WHITE BIRD, ID
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The gasket on our bottom drawer freezer was torn

Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!

Parts Used:

Refrigerator Freezer Door Gasket - Black

Pat from West Bend, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Ice Maker quit working

Removed 4 Stainless steel screw holding mounting assembly containing ice maker and motor. Unplug large plug from refrigerator inside wall and removed assembly. Closed refrigerator and lay asembly on flat surface. Removed ice maker plug from wire harness. Unscrewed ice maker mounting screws from mounting assembly. Reversed process to install new icemaker. Be sure to turn ice maker plug assembly to fit in holder on back of assembly and tape back in mounting assembly so assembly wil go all the way back in the door without forcing. If done properly, the ice bucket will slide in easily and the door to ice maker compartment will close easily without any problems.

Parts Used: