7002A Norge Dryer - Instructions

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.

First let me say that the video provided was wonderful, I followed the instructions on the video, & it worked great, no problems at all. Saved me from paying huge costs from a repairman.

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

Pull dryer out from wall about 6 to 8 inches step 1 - romove front/bottom access panel. Step 2 - remove lint trap and remove 2 screws (philips type) that is under lint trap door. Step 3 - push in 2 wood shime in front edge between lid and front panel (angled shims like door shims - a putty knife will work to, just be carful not to scratch finish) step 4 - fold lid upward and back (like on a hinge) step 5 - looking from where the bottom/front acces panel was losten 2 screws - one left one right about 3 turns - 9you can remove them it just makes it easier to reinstall the front panel. Step 6 - find appropriate pot or stacked 2 x 4 pieces - something to hold up the drum when you remove th front cover, and from underneeth support the drum. Step 7 - look thru bottm front access hole - there are 2 springs that come down from the door - and clip onto the frame of the fryer - unclip them and place on the side. Step 8 - remove 2 upper screws that hold front panel on, and remove front panel, if you left the bottom screws attached but loosened you have to lift up on the front panel a bit. Step 9 - looking from the bottom thru where access panel was - you will see motor on right with a additional roller (tensioner) - push upwards on tensioner to relieve pressure on motor and pop off belt (remember where tensioner is and how it clips in to base. Step 10 - work belt off of drum towars front - to remove it all the way you will have to lift up the drum slightly off of the pot or whatever you used for support so the belt can clear. Stem 11 - new belt goes on the same way you took to old one off - plat side away from drum with ribs against drum. Step 12 - again lift up on drum and work belt back on. Step 13 - tricky part is how to get the belt back on the motor - prentend you are threading a needle wht a folded over piece of thread - hold the belt with about a 4" loop with your left hand - hold up on tensioner and feed it back thru and work belt back over end of motor pulley, after front panel is back on with the 4 screws tightened spin the drum and make sure belt is between the 2 lines marked on the drum and remove the pot or whatever u used to prop up the drum. Dont forget to attach the springs for the door assemble all other components in reverse order. And dont forget to take the pot back out

I replaced it

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

Un pluged and Moved it out from the Wall, Raised the top, found broken belt. ordered belt on line, 2 days belt came in. cleaned all dust and dirt out put greese on berrings for rollers bleu out vent hose with Leef Blower. put top down, pushed back. pluged in and turned on IT WORKS!!!

My 12 year old son and I took off the front of the dryer to see if we could see what was wrong. The belt was snapped and on the floor of the dryer. I ordered the belt from you--it came three days later. That evening, my son held the drum while I laced the belt through the pulley. We cleaned everything up--lots of lint! Put everything back together, plugged it in, turned it on--SUCCESS! We were wildly excited. I am a stay-at-home mom determined to save money any way I can.

Shut off power and gas, unscrewed lint vent, raised top on angle with rope, unscrewed and moved door switch, unscrewed and took off front, put new belt around drum, then raised front end of drum with 4 narrow pieces of 1" foam insulation which let me view and install the belt connection to the drive motor shaft, adjusted the level of the drum using the rope holding up the top, removed foam pieces, replaced and rescrewed the front to fit the drum front channel, replaced the door switch, replaced the top and screwed it to the lint vent, returned gas and power, and ran confirmation test.

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

Followed the instructions and the repair went like clockwork, took less than an hour. I spent more time brushing and vacuuming old lint from the innards of the machine than I did doing the actual repair. Finished up $0.78 richer, too, from the change I found inside the machine.

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.

After using a voltage meter I tracked it to the thermal fuse. In order to get to the fuse you have to remove the heating element. However when I replaced the heating element I didn't check to make sure that the heating wires weren't touching the metal housing it sits in. So when I turned on the dryer I burned out the element and had to purchase another one so a simple repair became much more expensive. Since the thermal fuse is what blew initially I made sure to clean out the vent from the lint trap all the way to the outside vent. It was pretty dirty and probably caused the unit to get too hot and blow the fuse.

Pretty much just followed the video - I'd never opened a dryer before, so I'd watch a step, pause and do it, then run the video a few more minutes, and repeat. These dryers are really extremely simple devices: just a heater, then a motor to spin the drum and run the fan (I think the same motor does both). So you loosen a couple of screws, pry the metal case open, and slip on the new belt. Done! I didn't keep track of time, but I'm psyched to have saved myself a $200 repair call! Standard delivery arrived in less than two days, just like they said it would.