All Installation Instructions for Kenmore Range 66575963300

replaced oven lightbulb

very easy

Parts Used:

Light Bulb - 40W

peggy ann from forest city, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Inside Light would not work

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Parts Used:

SOCKT-LITE

Dan from Caddo Mills, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Trim at the bottom of the drawer was broken.

It was easy,and thanks to this company my stove looks like new again...

Parts Used:

Lower Drawer Trim - Black

Maria from Tampa, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

range handle fell off and screw got lost

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Parts Used:

Range Screw

Frances from palm beach gardens, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Light burned out in upper oven

Screwed in light bulb and glass protector

Parts Used:

Light Bulb - 40W

Shirley from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

oven light burnt out

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Parts Used:

Light Bulb - 40W

William from Schwenksville, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

3 of 10 people found this instruction helpful.

Was this instruction helpful to you?

light bulb went out in my oven

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Parts Used:

Light Bulb - 40W

Janet from Ada, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Parts Used:

Oven Sensor

Joanne from Negaunee, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bulb Replacement

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Parts Used:

Light Bulb - 40W

Judith from Phoenix, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 72 people found this instruction helpful.

Was this instruction helpful to you?

I broke the glass by hitting it with the edge of a broom

Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.

Parts Used:

Range Exterior Door Glass

Bernice from Phoenix, AZ
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Damaged Socket When Removing Bulb Base

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Parts Used:

SOCKT-LITE

Charles from Oceanside, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Replace oven door light switch

The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.

Parts Used:

Range Door Light Switch

Wayne from Sykesville, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Valve stem broke at the knob

Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.

Parts Used: