66572014101 Kenmore Range - Instructions

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

I broke the old trim when cleaning. New trim kit went together great. No screws needed because of new design. Best tip I can give is that the side trim pieces around the oven door go behind the glass on the door not in front of the glass. Visual instructions would be great.

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Took the old one out and replaced it with the new one, fits perfect.

Remove old grate and replace with new one.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Replaced both rollers....Quick and Easy!!

removed old and installed new

First remove the oven racks and the burner cover in the bottom of the oven. There are two phillips screws near the back. Loosen the screws but it is not necessary to completely remove them. Pull out the bottom cover and this will expose the burner. There is one phillips screw at the front of the oven and one at the back. Remove these screws and set aside. You should be able to remove the burner and unplug the wire connected to it. Replace with a new burner in the reverse order. Plug in the wire and make sure the new burner is seated properly over the gas valve. It lines up pretty easily. Put the rear screw back in but be careful not to drop it into the hole otherwise you will have to use a magnet to retrieve it or pull the oven out because it will be on the floor. Replace the front screw and put everything else back together. Pretty easy job

Remove oven racks. Remove bottom of oven. Mine was held in place by two large screws in the back part of the oven. They did not screw into anything. Lift out bottom from the rear. Remove burner cover plate by lifting the front and pulling out. Mine was not screwed in. The igniter is mounted on the burner and held by two 5/16 small bolts. The top one is easily accessible. The bottom is a real witch. You need 1/4inch socket set with universal connector to remove. There is a single wire attached to igniter by a wire clip. The wire is accessible by removing the bottom pan storage drawer under the oven door. Unclip the old attach the new. Screw two small bolts back in and replace things you took out. TURN GAS AND ELECTRICITY OFF BEFORE YOU BEGIN. Parts select should allow the igniter to be sold separately rather than connected to the burner. I only replaced the igniter. Replacing the burner would be a real chore.

Took off outer trim. Put new glass in and returned trim. Very easy, looks great.

The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !