66572004101 Kenmore Range - Instructions

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Took the old one out and replaced it with the new one, fits perfect.

Its was very easy, I unscrewed the old part and screwed on the new one and put the drawer back in place and it works perfect.

Looks better than the old one wes and so easy to do. Thanks.

Repair relativley easy only needed phillips screwdriver to complete repair.

Remove the bottom drawer. Remove the two Phillips head screws on the top inside of the door. Pull up on the handle (CAUTION: Be sure to hold the glass front against the door while doing this or the glass front can fall, possibly damaging it. Remove the glass front by lifting it towards the top of the door. Remove the two side pieces and the bottom trim piece by unscrewing the Phillips head screws located on the underside of the bottom trim piece. Discard the old trim pieces. Attach the new metal bottom trim piece using three of the previously removed screws. Do not tighten the screws at this time. Each plastic side piece has a nipple at the bottom. Insert this nipple into the outermost hole at each end of the bottom trim piece. The edge of the flange on each side piece should face inward. Have an assistant hold the two side pieces against the door frame while you slide the glass back in. The inward facing flanges go UNDER the glass. Reinstall the top piece making sure the indentations at the top of the side pieces are under the top piece. Install and tighten the two screws that hold the top piece on. Tighten the three screws holding the bottom trim piece.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

First make sure it is the gas valve not the ignitor. If the clicking sound still happens then the ignitor is fine, no clicking means ignitor may be broke and try to fix that first because it is cheaper. For us I knew it was the valve because the ignitor still clicked and the broil and top elements still worked. After the part arrived I turned off the gas and pulled the power to the oven. Disassembled all the components taking pictures along the way to remember what it looked like to go back together. Installed the new valve and use yellow gas tephlon tape at the seals. Put components back in reverse order. Run the top elements first to get gas in all the gas lines and remove the air. At this point the oven bakes again.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

First time was very difficult I tried to make the panel fit into the frame. Broke both side pieces of the trim.Even thouth I broke the trim PartSelect replaced them. I did not expect that.Second time it was easy. Remove the handle first and then the panel slides into the top and bottom only. It does not slide into the side of the frame but sits on top of it. Thanks, Allen

The kit was not supposed to fit my particular model but I felt the picture was exact and took a chance and had it sent. It was a perfect fit and was easy to assemble and looks like a new stove. I paid one third of the cost estimates that I got from local appliance centers and even other on line sites. I'm very please with the product and the delivery was more than prompt!! I couldn't believe the service!!! Thanks!!

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !