66517425792 Kenmore Dishwasher - Instructions

replaced the faucet adapter I did not save when I change out the kitchen sink faucet set

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

slid the pin into place, noting correct position of spring, backed hinge pieces with screwdriver and pressed door into place. Your video made it easier than ever. ( My 2nd time replacing the pin. ) Great repair experience.

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Removed the rack end stop by pressing the clip together using hand; removed the broken roller and rack support clip by snapping away from the rack. It was literally a snap to remove and replace. Very easy to do, my 12 year son could easily replace the roller assembly.

Ordered a new Faucet Adapter! Simple

Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.

I Tip The DishWasher On To Its Side So I Could See Under The Dishwasher .I New The Moter Was Working Fine. I Could Here It Runing While It Was Upright . So I Determind That It WAS The Water Inlet Valve . SO I Used A Pair Of Plires To Pull Back The Clamp On The Hot Wate Hose. I Took The Hose Off . And Then I Unscrow the Hose On The Water Inlet Valve That Takes The Water Out Of The Dishwasher.I Then Used A Small Werench To Take Off Two Small Scrows Holding the Water Inlet Valve To The Dishwasher .I Pull Out The Old Water Inlet Valve I Then Found The Modle Number And Seriel Number To My 20 Year Old Whirpool Dishwasher . I Then Went On Line Useing The Name And Numbers Found Partselect And Orderd The Right Part And Put The New Part In .It Took Me Less Than 15 mins And It Saved Me Maybe A Cupple Of Houndred Dallors..Thank You Partselect..

Unplug dishwasher from electrical, water supply and drain hose. Pull dishwasher out from under cabinet. Unscrew water whirler from inside washer, then remove motor. Remove black boot from motor. Unscrew keeper from impellor housing. And you are there! Pull impellor off motor shaft. Replace seal first, then replace impellor. So easy this girl did it. But, this girl also does small engine repair!

I watched the video, which was very good, and did the repair. It took about 10 minutes. Most of that was watching the video. EXCELLENT VIDEO!

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

Replaced the lower rack. The replacement part had the wheels attached. No assembly required.

removed the 2 water deflector and slipped the new ones in , in place.. very easy to do but it didn't seem to stop the leak so ordered the door gasket

The repair was so easy it was ridiculous...simply removed the end cap on the front of the roller assembly, took old one out, added new one and then put the end cap back on! Done in about 2 minutes!