6651678582 Kenmore Dishwasher - Instructions

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

Unsnapped the old rollers and snapped in the new ones. Worked great and easy. I was very pleased that the parts came so soon as well. Thank You, Ms. Cason

Turned off water and power. Used small nut diver to remove two upper screws from kick-plate, and loosen two screws in lower key slot of kick- plate. Removed kick- plate. Used plier to compress snap ring and remove hose to washer. Pulled off electrical connector. Used 5/6 wrench to remove copper water inlet. Used nut driver to remove two screws holding old valve. Once out removed the water connecting elbow from the old valve and installed it on the new valve. Reversed process to reinstall. Didn't even have to remove washer from the counter. My 25 year old washer is working like new again.

Watched "Steve" install the drain and wash impeller kit and then I did it.

The repair was simplicity itself. Remover the sprayer arm, removed the torx screws, replaced the seal, and reversed the process of disassembly. When I found out where the dishwasher was leaking from, I called KitchedAid and was ready to replace the overflow float. The part was 42.00 and wouldn't have fixed the problem. When I found this web site and read other peoples experience, I checked the pump seal, and it was obvious that it had blown out. That saved me a Loy of time and money.

I removed the rack and then pushed down on the old rollers to remove them from the rack. I then installed the new rollers in the same location.

screw it in then hook up the hose.

Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.

Old tandem rack for rollers popped off lower rack by applying a small amount of pressure. New tandem rack rollers look slightly different, but pop right in place. By replacing all four tandem rack rollers the lower rack glides smoothly in and out of the dishwasher. Entire replacement can be done without tools, by hand in less than fifteen minutes.

I used a screwdriver to snap off the old wheel carriers. When Ito attached the new pieces the tray wouldn't close. It was too wide. The person at Part Select was most helpful and patient but I still couldn't get them attached so the tray would fit. Then this week-end I visited my daughter and looked in her dishwasher, not the same brand but I could see how they attached, came home tonight and was able to figure it our easily. May I say a visual would have helped but your sales person was excellent.

followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

Dishwasher Stopped then only made a humming noise. Started with the Video on your site and it was quite helpful. I had trouble holding the drain impeller with the wrench. Used a drill to bore holes around the center and then broke the outer ring off to get a good hold on the center. Then was able to remove the bolt. The rest of the repair was easy. Something had caught the chopper blade and unraveled the spring. Replaced all the parts and it is working fine now.

Initially, I was going to call a repair-person to fix the dishwasher, but decided to check and see what was available on-line. I was very surprised to find a video on YouTube for my specific model. Even more surprising was the relative ease to perform the repairs, after watching the video. I have the proper tools, so I disassembled, per the video and found the problem. I was elated to see how easy it was to order the parts kit. It came in three days, and within 1/2 hour after parts arrival, I had the dishwasher purring like a kitten. What an excellent service. If you can turn a screwdriver, you can fix your appliance, via these well-done videos.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!