66515801890 Kenmore Dishwasher - Instructions

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

Unscrew the top bracket on basket of upper spray arm assembly. Remove entire upper spray arm assembly. Remove old spray arm. Install new spray arm and new supply tube being careful to align the upper bracket with slot on new spray arm and supply tube.

The repair was simple except for removing the thread portion of the old retainer nut from the lower housing. I had to remove the lower housing and separate the male threads of the old plastic nut from the female threads in the lower housing. That took 25 minutes since I did not want to ruin the female threads. Once removed, the new parts went into place easily.

No Water supply to Dishwasher. Turned off main Supply valve under sink.First took off old Diswasher supply valve and repaired it by cleaning it and it worked for two weeks. I ordered the part, but then cancelled it and Partselect service was great and cancelled it immediately. After it went down after 2 weeks I re-ordered it and it came in 4 days.
To Take this part off I removed mounting scews with nut driver, disconeected electronic plug connector, removed the compression fitting from the water supply and removed the outlet hose..reversed all of the above to install.

Removed the lower spray arm assembly thumb screw and lifted off the spray arm assembly. The lower seal had disintigrated - couldn't even find any pieces in the filter. After reassembly with the new seal and bearing I turned the spray arm by hand to ensure it was not binding. There was still was, what I would consider, some excessive wobble. I fashioned a shim washer out of some plastic from a Folgers coffee can lid and installed it on the thumbscrew threaded shaft and tightened it all down finger tight - it works very well and now, and no wobble.
I relaced the upper spray arm seal while I was doing the job (both the upper and lower seals are the same part #). I figured it would go out on me eventually, so I might as well replace it while I was doing the lower arm work. Kept the old upper arm seal as an emergency replacement.

Cleaned the filter screen of all debris (it is amazing what collects there over time). Cleaned the stainless tub with some spray Greased Lightning, ran the rinse cycle, and then put a few tablespoons of citric acid crystals in the soap dispenser and ran the dishwasher on NORMAL WASH with temperature boost.
Looks new inside; cleans the dishes, glasses and utensils well (no water spotting); and is nice and quite (like when it was new).

First I removed the plastic bolt that holds the wash arm in place This exposed the upper ring that was worn out . I then lifted the arm off which exposed the larger ring. I replaced that ring, and then I put the arm back on and replaced the upper ring. I put the plastic bolt back in place and the repair was complete.-- Really Easy plus the dishwasher gets the dishes clean now

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

You'll have to excuse me, but I'm a women and don't know the exact names for the parts.
Since my nut broke off in two parts, I had to remove the screws on top of the drain screen to get the other half. I just used a philips screwdriver and removed the 7 screws. Took out the broken part, and that was it. Put back the screws, put on the spinning water arm and put in my new part to keep it in place. Thank you. This saved alot of money for a repair person.

Removed the screw that held the mount in place. Snapped the new mount place (no screws required).

Fast & easy.

I removed the bottom spray arm and replaced the worn part. Now the arm turned freely and was performing as it was designed to do. I appreciate parts select for having the part available since the manufacturer no longer supported the model.

Removed holding stew from old style bracket. Put arm together with new mount and installed screw. Aligned arm with upper rack and just clicked on. Ensuring spray arm spun freely and done!

We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.

Followed the video. Only issue was that the panel mount screws cracked the plastic nibs that the screws threaded into. I replaced the screws with a Chrome sheet metal screw a bit longer and it held. Easy job!

I read a couple of stories about how easy these are to break when installing. So I used extra care, and made sure to push carefully in just the right places.

What worked for me was raising the tines of the cup rack to apply some leverage as I squeezed the clips into place with my fingers. No tools. No broken clips. No injuries. No cursing.

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.