66515702990 Kenmore Dishwasher - Instructions

First I removed the plastic bolt that holds the wash arm in place This exposed the upper ring that was worn out . I then lifted the arm off which exposed the larger ring. I replaced that ring, and then I put the arm back on and replaced the upper ring. I put the plastic bolt back in place and the repair was complete.-- Really Easy plus the dishwasher gets the dishes clean now

You'll have to excuse me, but I'm a women and don't know the exact names for the parts.
Since my nut broke off in two parts, I had to remove the screws on top of the drain screen to get the other half. I just used a philips screwdriver and removed the 7 screws. Took out the broken part, and that was it. Put back the screws, put on the spinning water arm and put in my new part to keep it in place. Thank you. This saved alot of money for a repair person.

We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.

Removed the screw that held the mount in place. Snapped the new mount place (no screws required).

Fast & easy.

I removed the bottom spray arm and replaced the worn part. Now the arm turned freely and was performing as it was designed to do. I appreciate parts select for having the part available since the manufacturer no longer supported the model.

Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

I bought the kit because it had other parts that I thought I needed.

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.

The nut had broken off even with the top of the threaded area, so we had to remove that broken part. We did so by using small pliers and inserting them in the opening and held them in a spreaded position while turning the broken piece out. We replaced the three new parts and put it back together and it works fine. So easy and much cheaper that having a repairman come in. Took us less than 15 minutes.

Pulled dishwasher out from counter. Took cover off and replaced door springs.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!