66515701890 Kenmore Dishwasher - Instructions

I first had to take the upper drawer of the dishwasher out so that I could get to the faulty part. This was a little tricky as there were two clips that had to be removed from the arm slides before the upper drawer could be removed.
I then realized that the faulty part DID NOT exactly match the repair part I received. The original connection wand was in two pieces where the repair part was all one piece. That required a bit of thought before I began the repair. There was NO drawing accompanying the new part, so I had to decide how the part would be connected. After a little trial and error, I determined the arrangement of the repair part and completed the repair. All in all, it went well, but there was a few anxious moments when I first saw the difference between the original part and the new part.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.

Pulled dishwasher out from counter. Took cover off and replaced door springs.

Easily installed the hose and replaced the middle spray arm with the help of my brother the savior! Lol. It was very easy for him to install.

The nut had broken off even with the top of the threaded area, so we had to remove that broken part. We did so by using small pliers and inserting them in the opening and held them in a spreaded position while turning the broken piece out. We replaced the three new parts and put it back together and it works fine. So easy and much cheaper that having a repairman come in. Took us less than 15 minutes.

Easy fix. It’s a screw on by hand piece.

Removed old rack opened box inserted new rack. So simple sorry I waited so long to replace.

Took out old rack, put in new one. Part arrived on time and was an exact match to the original.

Researched parts - 10 minutes - - - Ordered parts - 5 minutes - - - Waited for parts - 14 DAYS! - - - Installed parts - 5 minutes

New gasket did not fix problem. Cleaned air vent cover for steam to exit. Gasket not the problem but new one looks good. thank you

replaced those parts... but lingering doubts about adequacy of water supply due to sediment primarily from old iron pipes, evidenced in faucet aerator. So I added a Rusco hot water sediment trap filter to the supply line leading to the dishwasher and faucet, along with a new flex supply line to the dishwasher. Water supply seems improved, and any potential sediment will be caught by the trap.The time, tools, and complexity of adding the hot water sediment filter are not covered in the above.

I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.

door gasket old the vent was pluged up full of black slime cleaned out and door stopped leaking