66515629000 Kenmore Dishwasher - Instructions

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

Got the new door and tried to put it on. The door went on very easily. However, there's a spring that opens the door when the main wash cycle comes around. I never did get that spring right. None of the drawings showed the correct position and after an hour of trying to get it to work right, I gave up. The door comes open slightly (but not because of the spring) when it's time, and the liquid soap runs out due to gravity. But I wouldn't try to use soap powder because the door doesn't come open far enough.

1 Screw 5 minutes thanks for the quick service will definitely use ya'll next time

I ordered the upper and lower rack replacements PLUS additional wheels and other attachments because I could not tell from the schematic on the website whether or not the smaller pieces came with the rack.

As it turned out, the racks came ready to install and all it took was a limber nephew to take out the old ones and put in the new. Now I have plenty of spare parts in my own inventory in case the wheels, etc. need replacing.

I feel guilty sending you this repair story because all I did was order the parts on your website and then conned my nephew into making the exchange.

The parts arrived very quickly and in good condition. In fact, the new racks are an improvement over the ones that came with the dishwasher originally. Ms. Susan McNutt was quite helpful in keeping me informed of the status of the part that was back-ordered. It was a pleasure dealing with PartSelect.com.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.

I watched the video link sent in an email and followed exactly what they did in the video. I removed the star head screws holding the door liner in place. Then removed the protective cover on the inside. I disengaged the component holding the latch in place. I replace the component that holds the latch in place and then snapped the new latch in place. I turned the dishwasher dial until the prongs were fully retracted. I replace the protective cover and then put the door cover back in place. I initially only placed the left bottom star head screw until I was sure that the latch was going to release. I tested that it was working properly by slowly turning the dial on the dishwasher control. Once I knew it was working I replaced the rest of the screws.

Once the covers under the door are removed, the check valve is visible (unless its too dark, hence the headlight), and pointing right at you. Since I was working under the dishwasher, I gathered all the tools I thought I might need and laid them on the floor next to. Removed 2 covers, placed pan under check valve and hose to catch any water, squeezed clamp with (wrong) pliers, it eventually came loose. Carefully twisted hose off check valve. Water came out, some of it got into the pan, most of it on the floor. I guess I should have pumped it out before I started this. Plastic check valve is screwed into the big piece of whatever, carefully grabbed it with (wrong again) pliers and turned it out. Installation is reverse of removal - but use a large pliers with a ROUNDED jaw to grab the round check valve body. Don't squeeze too hard or overtighten it. Put the clamp on the valve before pushing the hose on. Be sure the hose seats all the way onto the little lugs. Compress the clamp, slide it over the end of the hose and release. That's all folks, works good now.

I used the screwdriver to pry the old lid off of the horizontal pin upon which it rotates. One must be careful before removing the old lid to note how the return spring is deployed. The short legs on the spring must be in the lip of the lid before you snap the new lid onto the horizontal pin. It was helpful to lubricate the two catches on the lid that snap on the pin with some liquid soap before attempting to snap them on the pin. After the lid is snapped into place and the short legs of the coil spring are in the lip of the lid, use needle nose pliers to attach the other end of the coil spring to the pillar where it was before you removed the old lid. There are videos showing how to do this on Youtube. The spring part is a little tricky. The video makes it look a bit easier than it is..

Mine is a Ultra Wash 111
I followed the repair video on your site but my dishwasher was a little different. Not enough that anyone could still understand the video and not get it disassembled. The video shows two ball checks but mine doesn't use them where the videos shows. I put them in anyway because I called Whirlpool, who made my washer, and they assured me that they should be in there. They got sucked through the dump impeller and plugged the discharge tube so I had to disassemble it again and take the ball checks out. Lucky for me nothing got damaged. I then got a hold of someone on your chat line that got me to the correct parts view that shows where the ball check is suppose to go on my washer. During working on my washer I realized the squealing was because the bottom bearing on the motor needed oil. So all and all I'm happy because it runs quiet and it works fine. Thanks Greg

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

repair was very easy did need to go to the hardware store for and adapter for the hose to water inlet valve as mine had a smaller diameter connector. Otherwise followed both videos. Needed a shopvac to remove water in the bottom of the dishwasher

First I read the other repair stories and knew it was a relatively easy repair. I removed the end caps on the front of the top dish rack and removed it for ease of access to the part. I then removed the two screws holding in the old part observing how it was positioned to make sure the new part was replaced in the same manner. I put the new part in place and screwed in place and replaced the dish rack. Everything is working just fine.

We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.

Removed the screw that held the mount in place. Snapped the new mount place (no screws required).

Fast & easy.