66513608790 Kenmore Trash Compactor - Instructions

bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.

remove drawer remove two phillip screws lift off front panel remove wiring and plug into new switch.slide switch through the hole in panel install nut reinstall panel screws and drawer job done.

Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.

Very simple, changed the gear, adjusted the drive and tested. Very straight forward.

The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.

I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.

took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together

easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.

very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!

Took the bent one out, put the new one in. The repair was not the story, the story was that we ordered the part on Monday afternoon and it was delivered on Tuesday! And the shipping was less than $8.00. Fresno to Elk Creek in less than 24 hours for that price was amazing!

take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.

Followed PartsSelect instructions, the Compactor was appoximately $1000. when I purchased it. The kit was $26.14. I will forever be a customer of this company. Thank you, Brian

Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed from the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.

I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screws from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .

Thanks to Parts Select and their detailed instructions it turn out great! Replacement Parts fit Great!