6651350190 Kenmore Trash Compactor - Instructions

Simply removed the two plastic gears (held on by some sort of clip), put the new gears in place using the spacing instructions that were provided in the kit ....... and it is working!

Took top off of the unit, then the 2 protective covers, Lifted Power ram out. Installed protector and new gear nuts. Reassembled... Done job. Great schematics and part list from Part Select./ Good delivery time as well. Will use again.

replaced rotary

-Removed the forward sliding rail screws...lifted the rails up several inches to access the wheel assembly...bent back the steel tab to access the nuts holding the wheels to the frame...replaced the wheels and bent back the steel tabs to original position. Trash bin now rolls out completely as before

changed out the switch and that fixed the problem

Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.

I removed the unit from under the counter. After removing all of the bits of old trash and making sure the chain and gears were not slipping or striped, I knew it was the power nuts on top of the ram. After all of these years they were worn out, almost smooth inside where the threads are. They were easy to locate on your website. I received them in 2 days (faster than expected) and in 10 minutes the unit was back together and working well. Today was the first bag to be taken out after the repair, it is much heavier than the previous ones, a sign that we are now packing much more trash in a single bag!

Someone pulled a Conan on the compactor handle and broke it loose--no one admitted doing it but I have my suspicions. Since the compactor was installed during the first Bush administration, I assumed that the part would be unavailable. I tried to glue it with the latest "super" bond epoxy/space shuttle goop and it would not hold. A friend tried to plastic weld the crack--it worked until Conan showed up again and ripped it loose. I was ready to look for a new compactopr but since it had an insert that matched the custom cabinets--that I knew would not fit on a new unit--I looked on the internet for a part.
The part number was entered, the part was in stock and the order placed on Sunday afternoon. The part arrived on Tuesday and was installed in less than two minutes. It was the high point of the week.

layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake

Removed 2 screws, pulled out old handle, inserted new drawer handle and replaced the 2 screws.

The drawer handle that was delivered was black and not brown. Black was the preferred color because the old handle was black.

This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.

Removed 2 screws holding the old part on. put the new part in place, re-attached 2 screws. Good as new.

Move the unit out of the cabinet, and take off the top cover.The two drive screws are easy to see. unscrew the two screws of one of the power nut covers and remove that cover. With pliers, unscrew the plastic power nut from that screw. Screw on the replacement power nut with the help of pliers and some heavy grease. install the bearing cap. Use the same procedure for replacing the plastic power nut on the other screw. To make sure the piston is level, place the cover on the power screw but do not attach it. Measure from the end of the screw to the top of the cover of the first screw, then adjust the second power nut up or down so the two power screw nut covers are the same distance down from the top of the it's power screw Lift up the piton assembly to close the gap, if any (I used a short piece of rope) , and install the screws on the second power bearing cap. After installation. recheck the distance from the top of the power screws to the power bearing caps is close to the same distance so the piston will be level.. This same procedure could be followed for other brands. Power of the appliance and verify functionality, if OK replace the top cover and push unit back into the cabinet..

First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!

pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.