66513409K900 Kenmore Dishwasher - Instructions

It just snapped in placed. Very easy.

used a screw driver, removed 2 screws, removed broken piece, screwed in new part ....all done :)
took less than 15 minutes to do*

i just wanted to let everyone know..I ordered the part on a monday and received it on wednesday I was amazed...the part fit perfectly ...and was very easy to install myself....ty so much ...

It was very simple, the repair took less than 5 minutes start to finish. I removed the top dish rack, took out two screws and the broken part slipped right off the water feed tube. I slipped the new upper wash assembly on the end of the tube and replaced one screw. My dishwasher is an older model and the new part only has a hole for one screw but I cannot tell any difference in stability or performance. I put the top rack back on and the dishwasher is as good as before.

Removed spray bar by removing the plastic finger thumb screw and replace as shown by you web page. Very simple.

I poked the old gasket with a fork tine so I could get a grip on the old gasket as I didn't have pliars, pulled it out in less than 4 seconds, folded the new gasket in half and started center top of the slot the old gasket was in and pushed the new gasket in on each side from the top to the bottom. Very easy. I'd say it took me longer to open the package with my teeth than in doing all of the above.

just put the pieces where they belonged and tighten the screws. it longer to figure out how it was supposed to fit than the actual fixing.

First I removed the nut holding down the lower washarm in place. I then lifted up the lower washarm where it's held in place by the nut. I replaced the two new parts: The lower sprayarm seal that seats underneath the lower washarm and the washarm bearing ring that seats on the top of the lower washarm just underneath the nut. A schematic parts list diagram can be downloaded on the KitchenAid website. The wobbling motion of the lower washarm still seems to have the same amount of play as it had before I replaced the two parts. The lower washarm itself is in fine shape including the nut. I even attempted several other different ways to install the seal and bearing ring, yet the washarm still wobbles when I manually spin it. I called KitchenAid to find out if wobbling of the lower washarm was normal. Unfortunately, the person I spoke to didn't seem to me to knowledgable enough in this area.

Simple easy twist on and off replacement.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

I manually attached the track stop to the right track in the disheasher.

I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.

I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.

Note I did not have a model number just the manufacturer and name on unit. The website was still able to find the part. Impressive!
Easy installation. I recommend you also get the sprayarm seal. Be careful to insure the nut is seated securely before screwing in the nut. Highly recommend the video. Good company.

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb