66513114K701 Kenmore Dishwasher - Instructions

replaced the valve

We took off the old one by disconnecting everything and put in the new one an re-connected everything. Aligning the pump was a little difficult.

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

put new hose on, very easy.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Just followed the YouTube video they sent with the receipt.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

Removed front instrument cover. Removed latch assembly. Tried to fix it . No luck. Ordered new latch assembly. Came in from partsselect in 3 days. Installed new latch. Replaced cover.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

After looking at what everyone else had done, I decide that I would take the dishwasher out of the wall space and set it on its side. This require me to turn off the power first. Then I pull the diswasher out from its space in the wall. I turned off the the water and then took off the water hose, then took of the return hose. There was water left in both, so there was a little water on the floor as a result of this. Then I finally pulled out the unit and laid it down on its side. The motor was very visible and was easy to access. The hardest part was finding the bolt to take it off. I pulled off the power connector to the motor and then took off the one bolt that was holding the motor on the washer. Then I twisted the motor, but it would not come off. I finally got a screw driver and put it in the small opening between the motor and the connection and it finally came off. This took all of about 30 minutes. Once I got the motor off, I notice that the aluminum grating inside was dirty and needed cleaning. So I cleaned this and put it back inside. The new motor came with every thing, so I put it in and twisted it. Then put back in the bolt, reconnected the power cable, put back on the water and reconnected the output cable. In order to make sure there were no leaks before I put it back in for good, I ran a short wash to check to see if everything was tight. There were no leaks, so I put everything back in the wall. It really did sound very nice now. This dishwasher unit came with noise padding, so I put that back as well. The dishwasher, now is very quite and I don't mind it running any time during the day. The hardest part about this is getting the motor off and find the bolt. It is down between motor and the unit and there was some aluminum between this and the dishwasher, so you need a long nutdriver to get it off.