All Installation Instructions for Kenmore Dishwasher 66513113K701

soap dish would not lock

12 screws remove door outside panel unplug wire remove 6 mounting screw remove old unit put new unit in place put 6 small mounting screws back plug wire in put front door panel in place put 12 door screws in your done now you can start and test run

Parts Used:

Dispenser

philip from THE VILLAGES, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

washer filled in when off..

replaced the valve

Parts Used:

Water Inlet Valve

Bruce from GRANDVIEW, MO
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

9 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Drain hose broken.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

Parts Used:

Drain Hose

Giorgio from Savannah, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench set

8 of 14 people found this instruction helpful.

Was this instruction helpful to you?

The Spinner at the top of the dishwasher came off and would not stay on.

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

Parts Used:

Spinner Kit

Ronald from SARATOGA SPGS, UT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

bones inside locked motor up and burned it out

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Parts Used:

Dishwasher Circulation Pump And Motor

Dawn from New Richmond, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench (Adjustable)

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Door spring broke-Door falls down

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

Parts Used:

Dishwasher Door Spring

Peter from JERICHO, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Changed front panel from White to Stainless Steel

Opened dishwasher door,removed 6 Torx screws, changed out panel, replaced screws. VERY SIMPLE

Parts Used:

Exterior Door Panel - Stainless Steel

Lowell from Manassas, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

One of the old stops broke

Snapped the new stops on. It took about 2 minutes.

Parts Used:

Dishwasher Rack Track Stop

Dwight from KENT, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Water pump was not functioning.

We took off the old one by disconnecting everything and put in the new one an re-connected everything. Aligning the pump was a little difficult.

Parts Used:

Dishwasher Circulation Pump And Motor

Pat from San Juan Capistrano, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable), Wrench set

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Leaking door seal

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

Parts Used:

Seal

Charles from ELGIN, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

There was no problem

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Parts Used:

Power Cord Kit

Briant from Byron, MN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

13 of 30 people found this instruction helpful.

Was this instruction helpful to you?

pump not working

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

Parts Used:

Dishwasher Drain Pump

Lois from HUDSON, NC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Rollers broke off top rack assembly

Replacement parts from factory installed using u tube support video

Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

Parts Used:

Dishwasher Rack Track Stop

Mark from WESTERVILLE, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Pump motor would not start

I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again

Parts Used: