66513044K113 Kenmore Dishwasher - Instructions

Our Kitchenaid dishwasher was leaking so I called a repair service. I gave the model number and serial number over the phone and explained the problem. I was told the rubber gasket would need to be replaced. When the repairman came 5 days later he told me that the gasket needed to be replaced but he didn't have a new one on his truck. He ordered one and said he would be back in a week to repair the dishwasher. That took 10 minutes at the most. He then gave me a bill for $200.49 ($71.49 for the part and $129 for the labor)that I had to pay right then. I wrote him a check so he would leave and immediately called the repair company to tell them the price was outrageous and that I had never before paid for a repair before the work was done. I was simply told it was their policy. I then told them I was stopping payment on the check - which I did. I checked on-line for the part and found your web-site and the the part I needed for $27.62. I ordered it on a Monday, it arrived on Tuesday and my husband easily installed it that evening. Thank you, thank you, thank you!

Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

Prepared by watching the video. Great instructions. Great.

Disassembled easily as per video. Removed the old latch and installed the new.

Began the reassembly and learned that after ten or more years the small plastic parts used to keep the dishwasher steady had slowly deteriorated to the point that I was breaking these necessary items faster than I was putting the appliance back together.

What was a half hour task became over two hours and the end result was for me to put my tools away and buy a new dishwasher the next day. I learned that if your appliance is over ten years old BUY A NEW ONE!

Great job by the people who make and sell the latch parts for you who own a dishwasher that is only a few years old.

Thank you Part Select.

Remove dishwasher from under kitchen counter. Lay down washer on it's back using some towels or other soft material to protect floor. Disconnect plug from pump motor and to get to the hose clamp easily I had to remove diverter motor. Be careful and slide diverter motor out slowly as it needs to engage the disc when putting back together. This took most of the time since I had to orient the disc slot with the diverter motor shaft that has mating tongue that goes into slot. Install pump motor but use liquid dish soap as lubricant to get hose elbow and pump inlet to slide in mating parts. Be sure to lubricate with same on tang that fits into rubber slot. Tighten elbow hose clamp with proper pliers for job. Re-install diverter motor assembly. Inspect for any oops's and install washer back under counter. Hook back up to drain, water and electric power.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

put new hose on, very easy.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.

remove 2 locks on metal roller guides. remove top basket. turn upside down on counter.remove spray arm by pryng one side in and lift out then push other side down and the out. install same as removal. line spray arm and turn clockwise til you hear a click.install basket and install locking plugs.

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

I simply removed the melted spray arm, then set the new spray arm in place, twisted the built-in securing nut (clockwise to its stop), and it worked without any problems.

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly