All Installation Instructions for Kenmore Dishwasher 66513043K113

I noticed my top shelf in my dishwasher was not getting the dishes clean

I read how other people had the same problem, I checked everything that could possibly cause this. I then believed I knew what was wrong. I ordered a new arm. It was unbelievable how easy it was to replace.it. It took less time than a minute. . Turn the nut holding the arm counter clockwise to remove the arm. To replace turn the nut clockwise I now have a working dishwasher. It is not necessary to remove the dish rack.

Parts Used:

Middle Spray Arm

Violet from SALEM, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The seal was bad on Dishwasher door, leaked

I opened the dishwasher door, removed the old tired seal in a manner of seconds. I measured the old seal against the new, same length, so no cutting. I started on one side pushing the seal in to the groove, made sure the seal was centered in the door. (not too long on one side or the other) It took less than 5 minutes to place the seal and check that it was all the way in, all around the door. I wiped the door down with some cleaner, where it contacts the seal. The door was harder to close, but I expected that until it breaks in. I ran a short load in the dishwasher with no leaks. :)

Parts Used:

Dishwasher Door Gasket with Strike - Black

Doug from Morgan Hill, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher leaked occasionally due to age and condition of old gasket

Repair was a "no brainer". Pulled out the old gasket, started the replacement of the new gasket in the lower right hand corner and worked all the way around the opening, then trimmed excess gasket of about 2" with a pair of scissors and I was done. Total time - less than 5 minutes.

Parts Used:

Dishwasher Door Gasket with Strike - Black

rick from sparta, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Roller mount broke Rack Adjuster

Took half hour to take off old Adjuster just trying to figure which things pop off putting on new one side 10 minute at the most

Parts Used:

Dishwasher Positioner

Dishwasher Dish Rack Adjuster Kit - Left and Right Side

Robert R from FOLSOM, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

6 of 11 people found this instruction helpful.

Was this instruction helpful to you?

The rollers on my top rack in my dish washer were broken and wouldn't stay on every time you pull the rack out it would fall. So I ordered the rack adjuster kit and it had everything I needed to fix it. Works like brand new now not hard to change and put new on took about 15 minutes approximately. D

Just remove from dishwasher the top rack and remove the old rack adjusters and put the new ones on , only 2 screws to each side and you are back in business. Very easy to change out. Put the rack back in slots in dishwasher and that's it.

Parts Used:

Rack Stop Clip

Dishwasher Dish Rack Adjuster Kit - Left and Right Side

Peggy from Sallis, MS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

it was the detergent dispencer, we had to install it twice. and it still does not work

like the instructions showed

Parts Used:

Dispenser

Sharon from ALTOONA, IA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

two retainers broke and the main part fell apart

pushed the new retainers in the holes and we are set to go

Parts Used:

Dishwasher Push-In Retainer Clip

Lois from Great Falls, MT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Would not drain water

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

Parts Used:

Dishwasher Drain Pump

Maynard from WISDOM, MT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher would not empty.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Parts Used:

Dishwasher Drain Pump

Walter O from CROYDON, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Friction sleeve came apart ....would not hold door in place

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

Parts Used:

Dishwasher Friction Sleeve

Gary from WAUKEE, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

drain pump noisy, broken piece of glass caught in pump.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Parts Used:

Dishwasher Drain Pump

David from OXFORD, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Door leaking

Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.

Parts Used:

Water Inlet Valve

Dishwasher Overfill Control Switch

Randy from Tucson, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

TOP RACK END CLIP BROKE OFF

PULLED BROKEN CLIP OFF AND SQUEEZED NEW ONE IN. I HAD TO USE PLIERS TO SQUEEZE TOGTHER SINCE i AM 77 YEARS OLD AND HANDS ARE NOT THAT STRONG ANY MORE. I HAD ALSO WATCHED THE INTERNET VIDEO TO MAKE SURE I COULD HANDLE THIS CORRECTLY. 10 MINUTES MAX TO UNLOAD TOP RACK AND PUT TOGETHER.

Parts Used:

Rack Stop Clip

Sonya from YOUNGSTOWN, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The old filter was warped, allowing food into the sprayer system

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Parts Used: