66513004N510 Kenmore Dishwasher - Instructions

Tipped over washer, removed attachment bolts, installed new pump by clamping water hoses. Be sure to use proper crimping pliers, not the generic slip joint pliers. Replacement pump included required new clamps.

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

Watched video, removed the door gasket and replaced

I followed installation instructions from this site and all went well.

As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.

The left side of the console broke during disassembly to get to the latch mechanism. This was to diagnose parts needed to fix a problem that the washer would stop multiple times in the middle of a wash cycle, requiring monitoring a wash to restart the dishwasher when the console light flashed.

Access to the latch mechanism requires removing two torx self tapping (in plastic) screws on the right side, two on the left side and two attaching the sliding latch plate to the console. Since the screws are tapped into thin plastic sleeves, breaking them can be expected, especially as the console ages.

The pictures available on the troubleshooting notes supplied with the parts diagram were very helpful; In the end I learned I didn't have to replace any parts involving the latch mechanism nor the electrical switch. I DID have to disassemble the latch mechanism and clean everything thoroughly of hardened soap "gunk".
The key to success, though was to NOT tighten the screws attaching the plastic latch mechanism to the console very tight as that will cause the sliding part to bind to the console so it can not fall completely on the switch, which caused the original intermittent operation complaint.

Removed the old pump, got part number from it, ordered the part. Simply a matter of slipping the new pump into place, reconnecting the electric, testing the machine out to make sure it did not leak. Then slid back in place with the cabinets.

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.

The dishwasher is 25 years old. Ordering the part was simple. Very good web site and user friendly. The shipment and delivery perfect. Part arrived as predicted. Tracking delivery was also perfect. Part was exactly what I needed. The only hitch was that there were no instructions for assembly, not even a drawing of the assembly to give a hint as how to assemble. Therefiore assembly took longer than it should have. However the diswasher is back in operation and I am pleased with the results.

Followed whirlpool Youtube available for DIY.

Caution....ensure that the pump POWER plug does not loosen when reinserting the pump/drain/filter (middle of dishwasher bottom). The plug can get offset if it hits the electrical conduit or water feed/drain hoses under the dishwasher.

Minimal water when disconnecting drain hoses...have towels at the ready.

Again, follow the Youtube video!

Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.

I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!

Disconnected power,water supply and drain.Had to pull dishwasher out to access the heater element nuts. Removed broken element and replaced with new part. Repair very easy!

this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.

Changed the seal first, very easy, no tools needed either. Helped a little, but still leaking a lot. Changed the lower spray arm and that did it. The video I watched before changing the seal helped a lot, definitely do that first.