6644428914 Kenmore Range - Instructions

With a phillips head screw driver we removed 2 screws pulled out the element about 3 inches and disconnecte the two wires from the insulated connection put the new element in replaced the element in the wall of the oven and replaced the 2 screws. Started the oven and we were good to go.

Part ordered on Monday, delivered on Thursday, put in on Thursday and cooking in no time. Very satisfied customer.
Thanks.

First I removed the two screws that hold the element in place with a 2' Phillips Head. I then pulled the element out about 3 inches and disconnected the two wires, with nose pliers, since they were semi-hard to remove the male from the female terminals.
I placed the order over the computer and it arrived in 2 days.
I was very pleased with PART SELECT.

Removed the retaining plate screws (Phillips), pulled out the element enough to disconnect the wires, disconnected the wires. Installation was the reverse.

btw, PartSelect shipping was phenomenally fast. I ordered this part on Saturday and it was at my door at noon on Tuesday!! Holy Moly...

I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. It was that easy. But the people at PartSelect.com were the ones that made it easy; easy ordering and prompt shipment. I got he part in approximately three days. Thanks PartSelect.com. You made me and my wife very happy. We didn't think we were going to have the use of an oven for Christmas. You came through for us.

I removed the two screws that hold the element in place and then I pulled the element out and slid off the contacs and it was disconnected in less than two minutes. When it arrived I installed the new one the same way in less than 2 or 3 minutes and while I waited for thepart to arrive I got a chance to clean my oven and so all is well, I am very pleased with my purchase. It is just that easy and I am happily baking again. Thanks, j. Cale, morrow ga.

On Saturday night before Thanksgiving my Wife indicated the oven was not heating up. A quick continuity check of the element indicated the unit was burnt out. I got on line and found PartSelect, found the proper element and ordered it. On Wednesday the element arrived and I removed the oven racks, removed two screws and pulled out the element to access the terminals. disconnected the wires, reconnected the wires to the new element and reinstalled the screws. Entire time was less than 5 minutes.

Thanksgiving dinner was saved at a reasonable price.

Unscrewed the two screws that held the old element to the back wall of the overn. Pulled out to reveal the two wires and connectors. Disconnected the two wires and removed old element being careful not to let the two wires recede back into the wall of the overn. Took the new element and connected the two wires. Then screwed the two screws through the holes in the element into the back wall. Easier than I thought it would be.

Could not believe that the part was here the next day! Install was simple,just connect the wires and screw it in.

I ordered part from Part Select, which literally arrived in 2 days. I unscrewed the two (2) screws holding the old bake element in the oven. Pulled out the element and detached the wires connected to the element, which was easily done without any tools. Attached those wires (again easily by hand with no tools) to the new bake element and screwed the two (2) screws back in. The whole process including ordering the part online, unpacking the box and installing took 15 minutes. Wonderful and in time for my wife and daughter to bake Christmas cookies!

simply removed screws & old part.., replcd new part & screwed back into place.

removed old bake element (remove two screws, disconnect two wires. install new element connect wires, replace screws to hold in place. turn on oven to be sure it works.

turned power off Unscrewed 2 screws pulled old element out slightly . disconected wires . connected wires to new element tightened 2 screws turned power back on baked a pie. took longer to type this

i received the part via fed-x i opened the box uninstalled the old part installed the new part turned it on the element got red hot and it works just fine.

Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.

I unscrewed the two screws holding the element in place and disconnected the two wires. Removed the element from the oven and replaced with the new one. Plugged in the two wires and replaced the two screws that secures the element to the back of the oven. Turned on the oven to test and turned back off when satisfied everything was O.K. Easy job.