6495-LWM-433 Amana Washer - Instructions

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Removed the damaged legs, replaced with parts from this site and leveled the washer .

Washer is old, but in very good condition. PartSelect was the only company I could find that had a replacement part. That included checking with Amana delears and other repair companies. The sequence of repair in 11 steps: 1. Unplug the washer. 2. Remove 6 philips screws (3 top,3 bottom) from the front of washer control panel to release the control panel. 3.Remove ground wire clipped to the timer. 4.Remove the knob. Could not unscrew,so I placed the tip of screwdriver against the end of the shaft on the backside of the bad timer and tapped to remove the shaft. 5. Use a 1/4" nutdriver to remove 2 screws securing the old timer. 6. Squeeze end tabs and remove control wiring plug. 7. Reverse steps 7 to 4. 8. Unscrew old shaft from the knob 9. Replace timer face plate (keyed to match new timer shaft only goes on one way). 10. Screw knob onto new timer. 11. Reverse steps 2 and 1. Note: It took me twice as long as it should of, I had the assistance of my 2 year old granddaughter Malae.

removed all old parts, put in new, saved a bundle

Replaced the timer and knob. Very simple..!! Works great now... dont have to struggle turning the washer knob anymore.

simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

First I removed 2 screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I connected the new value and put it back in place. I then put the screws back in place.

This was very easy and it solved my problem

Thanks a lot

Removed the cover on the washer controls. Loosed the knob and popped it off. Then disconnected the plug and replaced with the new part. Put th ekonb back on and closed it all up. It was pretty easy. Took longer to reomove all the screws than it did to remove and replace the part.

Followed video on PartsSelect website, they made it real easy.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

1. Removed the hot and cold water hoses. 2. Undid one screw holding on the solenoid mounting plate. 3. Pushed the plate in at the top to unlatch the plate at the bottom. 4. Pulled the plate out and undid the output hose. 5. Replaced the solenoid assembly held on by two screws. 6. Replaced it all in the revers order.

I pulled off the old metal sheath with a pair needle nose pliers....grueling....then gently slid on the new knob.

The repair was easy. It took approximately 30 minutes.

Took the timer nub off by unscrewing then the cover housing the timer unit . 6 Screws . 3 In front 3 in back . Cover came off easy. Un plug the power. Disconect old timer and replace with the new . Plug comes off easy by gently puling it out . Put back cover put back timer nub plug the power on and there it was back as new.