6443A Norge Washer - Instructions

PROBLEM: The washer lid has two hinge pins that are attached to the lid with Phillips screws (one per pin). The plastic pin that inserts into the hinge broke off, allowing the lid to come free. SOLUTION: First, I removed the lid from the washing machine. Second, I used a Phillips-head screwdriver to remove the original hinge pins from the lid. Third, I replaced the hinge pins. Fourth, I used a flat-head screw driver to pry up the washer top to obtain easier access to the hinge screws. Fifth, I removed the original hinges with a Phillips-head screwdriver (one screw per hinge). Sixth, I attached the new hinges to the washer lid. Finally, I attached the hinges (and lid) to the washer top, then lowered the washer top.

if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

The Repair went well . I had the hose on in about 30 seconds . The best part about this ordeal was the ease of finding the part on your website , and the speed of the delivery . I had my part in about 2 days , put it on and back to the fun part of clothes washing . I would recomend this company to everyone. Thanks, Rick K.

I removed four screws to remove a plate to get access to the pump. Then I removed 3 screws to remove the pump. I then put the new pump in place and put the 3 screws back in the pump. Then I put the plate back on and put the 4 screws back in. Then I put the belt on and put the washing machine back in place and connected the water lines and drain line and plugged the washing machine back in and then tested the washing machine to make sure it worked. Job completed.

I took the back off of the washer then took the old timer off when the new timer got here just plug in the wires to the new timer put the back on and it was like a new washer.
It saved me alot of money I was on my way out to get a new washer when I found your site on my computer

Once the washer was unplugged, i removed the two screws on the back pannel, disconnected the three wires, rubber water line, and two screws holding it to the control panel. Quite simply reversed the process with the replacement part i ordered, which arrived overnight, and the problem was solved.

unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.

Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!

I think normally the problem is caused by the Brake Rotor Lining Assy (item #50 on the diagram). It has a brake lining facing down that makes contact with item # 51. It turned out that I had grease & grime on these parts, thus the brake is not taking grip & causing squeaky noise. All I had to do was to clean the parts & put them back. I bought the part (#50) - P/N 2347192, but it was a whirlpool part that didn't fit my Magic Chef. Some parts fit both brands, but this 1 didn't. Here is the procedure:

1. Unplug washer.
2. Move unit away from wall.
3. Tilt it back far enough to work underneath. Support the front with lumber.
4. Pull out cap (#58)
5. Remove ring clip (#57)
6. slide out everything from #53 down. Keep them in same order for re-installation.
7. There are 6 ea screws (#53) that hold item #52 to item #45. It is spring loaded by item #47. Item #53 has a 5/16" hex head. Use 3 ea. #10-24 hex head screw, at least 1.25" long to assist in compress/decompress the spring tension. You can buy them from a hardware store.
8. Take out every other screw (#53) & replace them with these 3 longer screws for remove/re-installation of item #52.
9. Take out the remaining 3 ea #52 screws.
10. Go around & back off each of the 3 longer screws to decompress the spring.
11. Remove item #52, & everything from #48 down will come out.
12. Clean or replace what you need.
13. Do the reverse to put everything back.
14. There is an item within #59 that looks like a miniature bearing. I would put some grease on that & on item #55.

Leaned washer forward, removed clamp and old hose, replaced with new hose, reinstalling clamp.

Removed the old hoses and screwed on the new hoses.

I read some stuff on the internet where folks with the same problem replaced the water inlet valve to repair this same problem. So I did the same. However, after I installed the new water inlet valve, the problem was still there. It was at that point I decided not to guess at the what issue was and instead test the components in the washer. Yes, I am a lazy dumb ass. There are many of us out there. I decided to use a continuity tester to test all components in the hot water fill circuit and determined that the water temperature switch was bad. So I ordered a new switch from Parts Select (they rock - it showed up next day) replaced the water temperature control switch and...walla. fixed!!! Only took about 30 minutes to replace. Lesson learned: Don't be a dumb ass and guess. Test.

I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot

I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.

For this repair the tub must stay centered in the machine. I used a shim between the tub and front panel. Tilt the front of the washing maching aginst a wall and brace if needed. Remove the belt and pully. To remove the stator, I replaced 3 of the 6 bolts with a 2" long bolt of the same thread (replace every other bolt). This is needed because the spring is under 100# pressure. Remove the 3 original blots and than the 3 2" bolts. Remove each of these three a little at a time. Install the new stator and brake rotor. Use the 2" bolts in the stator to compress the spring. Reinstall the the other 3 bolts, pully, and belt.