62946779790 Kenmore Range - Instructions

I first shut off the breaker to the stove - safety first!

I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!

Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.

I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.

Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in. Plugged stove in and worked perfect.

First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new element, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.

My husband has moved out of state for his job. I am left here with the children until the house sells. This is the first time I have ever had to do any oven repair. I had excellent and fast service - my part came right away. I took out the 2 screws holding the element in place, pulled the element out, disconnected the old element, connected the new one, pushed it back in, and replaced the screws. No problem at all. I was a little nervous turning it all back on, but it is working perfectly!

First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.

I received the new element on the third day, followed simple directions, and voila! I'm baking again.
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!

I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.

Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!

switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering

Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk

Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.

Removed the electrical power. Lifted up the top. Slipped off the two connecting wires. Removed two screws. reinstalled new thermostat in reverse order.

First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.