62945765690 Kenmore Range - Instructions

Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done

Had checked the continuity of the baking element, was good.
Had checked the volts or was it amps of the temp sensor, was good.
That leaves the relay board.
Cut the breaker off, pop open the front of the burner lid, braced it with a wooden spoon.
Used needle nose pliers to compress 3 plastic mounting connections.
Held new board inside and replaced each connection one at a time to from the old to the new.
Press back into place, lower and snap on stove top, hit the breaker and there ya go. Fixed. Everything works again.

Removed the old element by removing 2 screws and disconnecting two solderless connectors. One solderless connector was melted in two. I had to remove the rear panel and cut the old connector off and crimped on a new solderless connector. The time required was lengthened due to trip to the hardware store to get a new connector. While I was fixing the oven element my wife replaced the oven light.

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

I followed peoples instructions here, and it was not very difficult.

Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place

Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.

Removed old hinges, fabricated new mounting plates from 16ga steel plate. . . Cut new hinges to fit in available space. . . Drilled and tapped new mounting holes and adjustment tracks. . . Shortened existing springs to fit new configuration. Installed new hinges.

Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.

Don Samuelson

Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.

John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600

Removed two screws and disconnected the element. Reconnected the new element and reinstalled the screws

removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.

Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy

POWER OFF! Unplugged oven from wall.

(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)

Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed the new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.

I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!