Models > 62942869 > Instructions

62942869 Kenmore Cooktop - Instructions

All Instructions for the 62942869
91 - 105 of 127
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bad burnes off on switch
Easy as Pie.
Parts Used:
Surface Burner Switch - 240V
  • Jim from Two Rivers, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner connecters lost contact
pulled he cooktop, replaced the recepticles, reassembled.
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch Surface Burner Receptacle Kit
  • tim from manchester, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner only operated on high, no medium or low heat.
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Parts Used:
Surface Burner Switch - 240V
  • Paul from Collegeville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
a few months ago, my daughter-n-law and I were hitting up tacos on the grill----the grates melted ---I thought I would have to purchase all of the parts even though only the grates were ruined---I am very pleased with my find with you.
just laid them down on top of burner and coals,----easiest installation ever----We are already grilling ----this is just like grilling outside but in AC
Parts Used:
Single Grill Grate - Black
  • Louise from Sherman, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
18 of 323 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
one pole of the socket corroded to nothing
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.
Parts Used:
Surface Burner Receptacle Kit
  • martien from williamstown, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner receptacle had malfunctioned and been removed
10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!
Parts Used:
Surface Burner Receptacle Kit
  • Kerry from Silverado, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burners would not come on without moving them around
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing
Parts Used:
Surface Burner Receptacle Kit
  • Ronald E. from Marissa, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner on stove didnt work
It was a very easy project...Removed the stove top a few screws..snipped a couple of wires and attached the new receptacle...everything needed was in the package...They even have a video on here that was very helpful..shows how easy it really is...
Parts Used:
Delta Frame Surface Unit - 8 Inch Surface Burner Receptacle Kit
  • Timothy from Greybull, WY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dropped cast iron pot broke switch shaft off
The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!
Parts Used:
Surface Burner Switch - 240V
  • Robert from Clive, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner was very hot regardless of setting
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.
Parts Used:
Surface Burner Switch - 240V
  • David from Woodland Park, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Parts Used:
Surface Burner Receptacle Kit
  • Darwin from wisconsin rapids, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
heating coils would not work
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Parts Used:
Surface Burner Receptacle Kit
  • Adam from Kempner, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Burner did not heat
New receptacle element. I am a girl and I did it.!!!!
Parts Used:
Surface Burner Receptacle Kit
  • lula from Antelope, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
switch on top of stove
James is an electrician so he istalled the part himself
Parts Used:
Surface Burner Switch - 240V
  • James from Beaufort, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Burner would stay on high, on all settings.
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.

Thank you for your help!!

Bob
Parts Used:
Surface Burner Switch - 240V
  • Robert from Attleboro, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 62942869
91 - 105 of 127