62629 ((ABKESEA)) LG Range - Instructions

Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.

I went to LG website enter model number and was given a list of parts that need to be replaced with a percentage of which part fails the most. I order micro switch PS3522738 which arrived and PS3529293 was backordered. I installed the one that arrived. The microwave worked briefly. I reordered and waited for both switches to arrive and installed both. The microwave still doesn't work.

You Tube

I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.

https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs

Removed the phillips screws from the base.

Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)

Replace the spacer, which is a separate part from the motor.

Reinstall the spacer and motor.

Reinstall the bottom panel.

Enjoy!

Easy, and the microwave still doesn't work.

Took a putty knife and our the inside trim molding around the glass loose used a phillips screwdriver to remove old handle and install new handle popped trim piece back on.

Took off cover and checked all of circuits (& fuse). Had continuity until I got to turntable motor. Little motor on bottom of micro.It did not have continuity. I thought - looking at circuits - it had to be motor. When I got new motor - I was surprised there was no continuity through it but I was confident it was what I needed . But motor in & tested & worked fine. GE was no help at all! No useful info at all online! No schematics! The motor Had been discontinued ( thankks to info from Partselect.com). Partselect.com found a replacement part (& #).

i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell

Pop old one out and replaced it with new one.

Removed door from microwave and then popped the inside widow trim ring off. Removed 4 screws from the window bracket, replaced the latch with a new part and then assembled.

very simple

Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

Took the tray out of the padded box, and put tray in microwave. That easy, no tools required.