62190449 General Electric Dryer - Instructions

I followed the instructions in your detailed online video. Fortunately on my model there was a removable panel on the back of the dryer which provided easy access to install the drive belt on the motor pulley and the idler pulley. Great video and very easy repair.

Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.

Put the knob on and turned.

Opened the package. pushes the new knob on and voila it worked! It was very easy.

Just placed it where it belonged.

Open the door and removed the part. Installed the new part and started the dryer.

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Watched video instruction, paying attention to what it showed in machine. Several virsions of similar designs over the years, look over yours and note access points, take pictures as you go! Just pay attention, it is very logical. Spread the side panels to get the drum in and out, and pay attention to drum axel in back and the bushing it rides in. Be patient, be firm but gentle, no real forcing needed if you are alligned. Be sure the grooves of belt are on the drum, drive wheel on motor, no twists. Reverse order to reassemble. There are several internet videos of models with same basic setup, so look at others if one doesn't show the detail you need to see, or clear some uncertainty. Your local hardware to sorce push fastening for the idler wheel to shaft if you mash it up, they are cheep and several styles will work.

Removed the top, four screws under the front inside the open door. Then the removed the front, two screws inside at top by drum and two screws on bottom. Then pulled out the drum, from there I was able to get to the bearing that was bad. Mine was a older model than the instructions showed that came with my repair parts but it was colse enough to get the job done. Your website is AWESOME!!! The entire experience was wonderful and made my repair as painless as possible. I have already recomended it to my friends, keep up the great work.

Simply pull old knob off..slip new knob on. Less than 2 seconds...done

- Removed two screws at top left and right of door.
- Removed top dryer panel
- Removed two screws holding front panel in place
- Noticed drum slide was missing because front drum bearing was worn away and slide had fallen off.
- Went ahead and removed drum to replace rear drum bearing (probably not needed; should have disassembled it first to discover this). Would have been better to pull drum first (loosen idler pulley and release belt, pull drum straight out) instead of attempting to unscrew bearing. Be sure to note how the idler pulley is set.
- vacuumed tons of lint up
- Replaced bearing (needed a second person for this; drum too big to reach around. be sure to pre-thread the bearing)
- Ordered front drum bearing, waiting to repair it now, should be good after this.

Had a repair shop quote 230 for repair . Spent 66 on parts and did the repair in 45 minutes using the instructions from folks on this site . Very happy with results thanks

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 screws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.

Used online instructions. Worked well.