6002A Norge Washer - Instructions

Opened hinges top of washer. Removed screws holding hinge bases. Removed the washer top lid and unscrewd broken hinge pin. Replaced hinge pin and inserted in pin base and screwd base op hinge back onto washer and job was done.

Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.

I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!

The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I finally decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]

I followed Gary from Sioux City IA instructions. Very well explained.

changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks

I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!

Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.

Removed back access cover and lift top cover looking for leak. Initially thought it may have been the pump housing. I filled some water into the tub and I flexed the hose between the tub and the pump and water sprayed out. It had cracked in about 3 small places (water is present in the hose anytime water is in the tub) Ordered and replaced hose. Also order drive belt and replaced as a preventive maintenance item.

We have a Jenn-air washer & dryer that we bought new & are now almost 15 years old. I just put about $20 into the washer that took me about 20 minutes to do the repairs. Change tub to pump hose & lid hinge pins. The dryer was about $40 to fix. Blower wheel & drum rollers. That repair took about 40 minutes. Both units you have to take the front cover off & that will expose just about everything. A screw driver between the top & front will pop them open. One hour & $60 in 15 years. I think we made a good choice.

Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket

Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.

Always test the air bell before installing an outer tub.