All Installation Instructions for KitchenAid Mixer 5KSM195PSABK0

Motor would not turn on

Initially removed carbon brushes then inserted the new carbon brushes. The motor still did not turn on. Then I removed the brushes again, used a flashlight to look in the hole where the carbon brushes are installed. I noticed that there was a square notch on one side of the hole. I then reinstalled the carbon brushes, ensuring that the beveled side of the carbon brush was installed so it lines up with the square notch. This allows the carbon brushes to touch the motor. I turned the unit on and it worked.

Parts Used:

Mixer Motor Brush

Paul from Reno, NV
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

The head of my machine was sagging

and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED

Parts Used:

Mixer Dowel Pin

Lee from Valencia, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Pin fell out of neck

Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!

Parts Used:

Mixer Dowel Pin

Tiffany from San Antonio, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Mixer bowl was slipping off the base when in use

Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.

Parts Used:

Mixer Screw Cap

Dean from Fairfax, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Wire Whip was coming apart

Replaced it with a new part. No installation or repair to maching was necessary

Parts Used:

Wire Whip Mixer

Lois from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

bent wisk

replace wisk order process very efficient and delivery prompt.

Parts Used:

Wire Whip Mixer

Franciska from Carrollton, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Food mixer suddenly stopped without burnning smell

Just change the motor brush. That's it! It work well now. Thank you, Partselect!

Parts Used:

Mixer Motor Brush

Takahiro from Arlington, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Bent wires in a wire whip

I ordered a new wire whip and attached it just like it was the original. WALLA!!! Done.

Parts Used:

Wire Whip Mixer

Robert from Blairsville, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

needed new brushes for a mixer

Easy to locate part I needed (brushes)..great diagrams Thanks

Parts Used:

Cap Spring

Linda from St. Cloud, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Screw cap or retainer wore out and wouldn't hold the bowl tight

Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly

Parts Used:

Mixer Screw Cap

Robert from Aitkin, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Sticky back disc on Orbital sander came apart (from old age )

remove 3 screws ,remove old sanding disc replace with new installl screws

Parts Used:

Worm Gear

David from Tolland, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

original part worn out, wouldn't hold mixing bowl

unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.

Parts Used:

Mixer Screw Cap

Diane from Holland, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

The screw cap no longer held the bowl in place.

This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!

Parts Used:

Mixer Screw Cap

Roberta from Glen Ellyn, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Worn spring would not allow atthing mixer attacments

Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.

Parts Used: