All Installation Instructions for Whirlpool Mixer 5KSM175PSEDR4

Replaced worn out gear

Fairly easy if you have done it once before.

Parts Used:

Worm Gear

Mixer Retaining Pin

Richard from SUQUAMISH, WA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Wasn’t spin any moore

Follow a YouTube video step by step

Parts Used:

Worm Gear

Rosa from GLOUCESTER, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

noisy

disassembled replaced part reassembled now works well

Parts Used:

Bearing Bracket

Mixer End Seal

Brian from SPOKANE, WA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken beater shaft

Used the diagram on the website and a video
Totally worked!

Parts Used:

Agitator Shaft

Glenda from SANTA FE, NM
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Base plate destored

I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws

Parts Used:

Mixer Screw Cap

Gordon from West Stockbridge, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Old screw cap wore out and would not hold bowl when mixing heavy batters.

Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.

Parts Used:

Mixer Screw Cap

Sharon from FAIRFIELD, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

None

I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!

Parts Used:

Mixer Motor Brush

Mixer Brush Holder Cap (Black)

Cap Spring

Mixer Spring Cap

Mary from RICHMOND HILL, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Screw cracked on the front of the mixer

Skewer the screw in with my fingers,

Parts Used:

Mixer Thumb Screw

Mrs Brenda from LYNNWOOD, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

bowel would come out of screwcap when making dough for pasta

The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.

Parts Used:

Mixer Screw Cap

Robert from AURORA, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old wire whip was broken

Just put on the new whip...exactly like old one.

Parts Used:

Wire Whip Mixer

Stephanie from JACKSON, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Very Happy

Easy

Parts Used:

Wire Whip Mixer

Joel from Mount Clemens, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

no mixing

dis-assemble, replace part, re-lube, reassemble, test good.

Parts Used:

Worm Gear

per from highland, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Attachment hub stopped spinning

Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!

Parts Used: