5KSB52EWH4 KitchenAid Blender - Instructions

Per directions, I pried the drive off the screw. I was surprised that the drive came off the screw by just a prying action, but that's how it's done. The metal base to the drive is softer than the screw so there was no stripping of the screw threads. Then I just threaded the new drive onto the screw and done.

The longest time spent was in getting the part out of the package and reading the directions. All told it took less than 5 minutes.

The rubber part of the drive appears to be very brittle as it chipped off the drive gears. But it was easy to repair and they do last about 5 years.

Exactly as described in installation instructions included with new coupling. Great feeling hearing the sound of the motor and fruit being chopped. Mission accomplished!

When I googled the part I got a video of someone replacing it. It looked so easy I order the part and followed the instructions. Amazingly easy.Thank you.

Use the purpose made wrench to hold the drive shaft while unscrewing the broken coupler from the drive shaft. The shaft has a left hand thread, so turn the coupler clockwise to remove it from the drive shaft. Then screw the new coupler onto the drive shaft, turning it counter-clockwise. That's it!

Just follow directions included with part, very simple and understandable. GOOD BUSINESS, THANK YOU

I watched the video on the website and I realized I could repair a $100.00 blender myself, for under $20.00! So, so easy and the part came in two days. Great company, Thanks!

I followed the included instructions.

Removal of the old coupling was easily done by gently prying it up. The threads on ot are much softer that the shaft.

Screwed the new coupling on and done.

I also bought two of these couplings as the rubber on it WILL break off again.

pry rubber up enough for vice grips, unscrew coupling,left hand threads,screw on new. Came with instructions, in English.

To start with the coupling, I followed the directions by using a flat screwdriver and a thick towel. I placed the towel under the screwdriver to protect the base unit from damage as I pivoted 1/2 of the tip under the coupling, pulling it up as I went around until the coupling popped off. Then I cleaned the remainder of any metal left behind. Then I attempted to screw the coupling on clockwise but the screw opening was slightly to small. So I plugged in the unit and held the coupling with the screwdriver in place and turn the unit on stir and it screwed it on clockwise.
Next, the seal was replaced at the bottom of the jar. And I was finished. Easy as pie.

Because the old coupling was so tightly screwed onto the shaft it was necessary to use very flat wire crimpers to slide between the old coupling and the blender housing to grip the shaft and immobilize it while pliers were used to grasp the old coupling and loosen it---rotate clockwise.

Part is left hand thread. Use screwdriver to lock motor fins and twist off part.

I followed the instructions on the sheet that came with the replacement part. The instructions are accurate, however, the working is misleading. I think additional information is needed to make the install easier. First, a flat head screwdriver works best. Also, all the rubber that is on the broken coupling needs to be removed before trying to get the coupling off. Once all the rubber has been removed then it becomes easier to see the metal rod that holds the coupling and distance between the coupling and the base of the blender, take the screwdriver and gently pry the coupling off in an upward movement while going around in a circular manner. Then you can see the coupling rising up from the rod. Then take a hold of the broken coupling and pull it off. Then attach the new coupling, screwing it on counterclockwise. Once you realize what is going on, it's actually quite easy.

Forget about the repair blogs. The coupling includes a repair instruction sheet. It actually took longer to read the sheet than it did to do the repair. Follow the repair sheet instructions. Very easy, however not intuitive.

The repair is easy. Just follow the directions that come with the replacement part. And parts select is awesome. I received the parts within a couple of days and fixed it right away.

I will definitely use this company again. The blender was over $120 when I brought it and I did not want to spend that kind of money again. My cost to fix was about $8.00 for the part and $7.00 for shipping. Hmmmm, $15 vs. $120+ sounds like a good deal to me.
Thank you.

Last time this happened we simply used a thin wrench to unscrew the damaged coupling. This time it was so tight no wrench could undo it. We had to grind it off using a grinder drill until it was so loose it popped off.