59689592101 Amana Ice Maker - Instructions

I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the bracket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!

Simple remove the fan and motor, plug in the new cord and screw in the new motor.

It was very easy. The part make look different online but it was a proper replacement.

Pull cover off in front of ice tray and ice grid cutter to make easy to get at temperature sensor wire connector. remove connection plug to temperature sensor remove screw on side of ice bin that holds sensor in position.
Put sensor in a class of ice 32 degrees and measured resistance read 6.2K should of been read 8.7K Ordered a new Temperature sensor from partselect.com . Installed in 5 min working like a champ again.
The instructions book call the part I need a Bin Thermister instead off temperature sensor.

I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembly,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket

Tools needed:
- 1/4 inch nut driver or socket & ratchet (or wrench... depending on what you have available.)
- Optional: Flashlight and mirror

1 - I turned the power off.
2 - Grabbing the bottom of the cover (above the ice bin) with both hands, I pulled sharply toward me and the cover was free.
3 - I used the nut driver to remove the screw holding the thermistor in place against the wall of the ice bin.
4 - I used the flashlight and mirror to confirm the placement of the connector.
5 - Used my index finger to depress the locking clip and gently pulled the connector downward.
6 - I attached the new thermistor to the ice bin wall using the nut driver.
7 - I threaded the connector up to the control board and pushed it into place. (This step was the most difficult for me... I had to use the mirror to confirm that I was properly aligned.)
8 - Turned on the power (and shut off the "FAST ICE" option -- may not be available on all ice maker models).
9 - I scooped out a gallon of ice for my tea maker.
10 - A few hours I checked the bin level to confirm that the ice maker was behaving.

All in all, a very simple repair and certainly beats paying someone $200 or $300 for a five minute job.

Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.

First let me say that the instructional video on your website for this repair was very informative. My son and I watched that before we began the repair. We unplugged the unit first. After removing the back cover, he unplugged the old fan's electrical connection, and then proceeded to remove the fan and bracket from the unit. We then removed the old fan from the bracket, installed the new one and then he reinstalled the new fan and bracket back into the unit. He used the included electric adaptor cable to complete the electrical connection, plugged in the refrigerator briefly to confirm all was well (it was), then replaced the back cover and we were done.

I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.

Replaced thermistor u

I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.

Unplugged the fridge first then took the bottom panel off with a 1/4 inch nut driver. Disconnected the wiring & used my ratchet to reach the 3 screws that held the motor. Took me longer to clean the bottom of the fridge then the installation.

Instead of hiring a technician to repair my 2022 Kitchen Aid ice machine for parts, labor, & service call of $300+, I decided to research a little. Google & U-Tube directed me with what was most probable wrong & walked through exactly how to replace part needed. The secret or guarantee correct repair is to use OEM parts only. $59.50 later with OEM part from this site/ Fixed and working as new again. Thanks .

stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.

I suggest following video supplied with order confirmation perfect fit