59679519012 Kenmore Refrigerator - Instructions

changed the starter connected to the compressor

Lifted out the glass shelf and then removed two screws to get the right side end cap off. This side has a mechanical slide to adjust the amount of cold air into the Deli area.

You will need to carefully remove the plastic slide linkage from it's guides so that you can turn it sideways and it will then come off the end cap.

If it wasn't for that minor slowdown it would be a five minute job.

Thanks to this web site for QUICKLY getting me the part and providing info on how to do the job.

Removed the old gasket and made sure we put the new one in the same way. A wooden mixing spoon was the best tool for pushing the gasket into the track without hurting it. We used the back of the spoon and it went right in with no problem.

Really was very easy to do.
I read how others completed the replacement & followed instructions that came with the replacement gasket. Original gasket (new in 2008) was at first stubborn to remove but once I got it started was easy to complete removal.
The new gasket arrived folded in half. I followed the instructions to eliminate the bends and a few crinkles with heat by laying the gasket in direct sunlight until it was warmed and pliable. I cleaned the gasket areas and then massaged the warmed gasket until it was smooth & fully shaped. It was then very easily to install.
So glad I decided to order this original part form this site and install myself. Saved a lot of money plus enjoyed satisfaction of doing this myself

Took the new door seal out of the box, layed it out as straight as possible heated it with hair dryer 4 1hour took the old 1 out by hand and replaced it with new one no tools needed 10 min job

Snapped new cover on.

Removed drawers and glass top and support bars Two screws on slid bar two screws on end cap, Make sure you take time to remove air control it has two pivot points with small taps.
Then just replace parts as you had taken off very easy.

Beware - the website does not indicate that doors are different sizes on this model refrigerator. Not paying attention I ordered 2 of the same size gasket which only fit the right side door - had to send one back and reorder left side from Whirpool directly.

The actual installation is very easy. It may take a day or so the gasket to feel like its actually making a good seal.

lift glass, slide new rail in replace glass. 2 min repair.

Removed the crisper drawers (pull out, then up & out), remove the glass shelf above the "pantry", remove the pantry door (easy because hinge stud was broken), then remove the pantry drawer. Use 1/4" nut driver to remove the broken LH End Cap...it pulls up and out. With the phillips screwdriver, remove/replace the steel rail for the drawer action to the new part. Replace in reverse order (after your neat freak SO cleans everything!).

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

unplugged the unit pulled it away from the wall removed the lower panel removed the drain installed the new replacement . removed the wiring harness and replaced it with the new one replaced the panel and plugged back in

Laid gasket in direct sunlight for an hour, heat made it very pliable. Removed existing gasket from door groove, which came out with little effort. Pressed new gasket in door groove with minimal effort as it was pliable from sunlight heat. Gasket seated correctly and resulted in tight seal.

I watched the video provided on-line in your website, which was excellent. The information provided gave me everything I needed to change the board. I already had experience handling control boards and was aware of the static precautions; however, your paperwork was very good detailing how to program the new board. The only small problem I had was reinstalling the temp sensor in its bracket. The lead was very short. Other than that, all went well! The project took between 20 and 30 minutes.

Old gasket was pulled off with ease. New gasket came folded in-half in cardboard box and was flattened in several places. It was reshaped with ease with the heat from ny wife's hair dryer. Insrallatint took about 5 minutes and seal was perfect. Took less than 15 minutes total.