59679313511 Amana Refrigerator - Instructions

The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one orientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.

Very simple fix, remove 3 screws, two connectors to the old switch

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

Unplugged fridge
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done

Followed some online videos. The replacement part actually matched exactly what the videos I found showed. It was my refrigerator that was slightly different where the unit would mount/screw into. The old unit had a bracket which easily attached to the replacement part. It is less than a 1 hour repair for sure. But it took me a few minutes to figure out the bracket adapter. Plus I forgot to seat the ice maker shut off bar and had to disassemble some things again to get in there to seat it properly. Part was shipped quickly and securely !

Super simple following the instruction video you posted. Thanks!

Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!

DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.

Unplugged wire plug, removed mounting screws and removed ice maker. Installed new unit by reversing steps--

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

replaced water valve still does not work

Have part need instructions to remove old and install new

The fridge would occasionally run warm, requiring me to turn it off and defrost the evap coils in the freezer. I found an online video that demonstrated the entire process of replacing the control board. The fridge model in the video was different than mine, so it took some time to figure out how to remove the panel. Once that was done, the rest was easy. The only tool required was a flat-head screwdriver that was used to push in the tabs holding the panel in place. The circuit board took more effort to split in two than I had realized, and I had to be careful not to bend any of the components on its surface. The whole process took less than 30 minutes, and the fridge is working properly now..

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.