59679249013 Kenmore Refrigerator - Instructions

Removed the shelf below the cover to allow plenty of room to work spread apart the old cover at the pivot point toward the back installed the new one in reverse order

The glide was very easy to put on; however it is easiest to put in the front screw first, due to the thickness of the glide. Pretty easy!

Just plugged it in

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

Looked up a video on utube. That was a big help. The new ice maker didn't come with a insulation guide.

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Followed video

Like you video

I opened the large cardboard container the way it appeared to have been sealed. I knew i was dealing with glass. It was packed soooo great! After opening I Saw that the glass was tucked behind a separate piece of cardboard. Glad I had laid the package on the table to open. This made it easy to lift up out of the package. I went over the glass with a slightly damp cloth and dried. Peeled off the little stickers and laid it on top of the shelf supports and middle divider. It rested down right on top and eased into place. Wah-la!! All done! Thanks! Easiest repair I have ever had, and I am almost 70 with a lot of history in repairs!!

I took all items off the glass shelf. Removed the two crisper drawers. Removed the glass shelf. Installed the center rail. Replaced the two crisper drawers, the glass shelf and all items. Job done in less that 1 min. Thank you for great customer service and quick delivery.

Just put it into the bottom of the fridge and it snapped into place. NO PROBLEM AT ALL.

Lift off glass shelf and insert tabs of rail on each end , replace shelf.

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!