59678539800 Kenmore Refrigerator - Instructions

Replaced with new gasket

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

well, first, after calming down i removed the glass from my sink (this took a half hour). then i went to the computer and looked for jenn-air parts. the part-select site came up. the site was very easy to use and although i usually leave things like this for my husband to do i decided to order the part myself, which i did.
the trick was finding something on hand to cover the tops of the crispers which were both full of vegetables. i innovated and used a shallow broiler pan and its lid which covered 90% of both the crispers. the part came in five days unwrapping the part was easy, cleaned it with windex (no sink soaking this time) and inserted it on top of crispers............totally easy!!!!!

Snapped new cover on.

Removed drawers and glass top and support bars Two screws on slid bar two screws on end cap, Make sure you take time to remove air control it has two pivot points with small taps.
Then just replace parts as you had taken off very easy.

lift glass, slide new rail in replace glass. 2 min repair.

Removed the crisper drawers (pull out, then up & out), remove the glass shelf above the "pantry", remove the pantry door (easy because hinge stud was broken), then remove the pantry drawer. Use 1/4" nut driver to remove the broken LH End Cap...it pulls up and out. With the phillips screwdriver, remove/replace the steel rail for the drawer action to the new part. Replace in reverse order (after your neat freak SO cleans everything!).

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.

Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!

Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.

Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.

But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

followed the instructions provided and that's it!