59677533603 Kenmore Refrigerator - Instructions

Empty drawer and take out . remove glass shelf and front and rear shelf braces. remove 2 screws holding pantry end cap to fridge. remove rear bracket by unsnapping clips. remove temp control arm. and reattach to new end cap. reinstall rear bracket to fridge and align end cap, align screws and tighten. reinstall drawers and shelf brackets. replace glass shelf. and reattach lid to brackets. Open beer and enjoy success.

First I removed the pantry drawer; then the two crisper drawers and glass shelf. Then I removed the hex screws that held end cap in place. Removal of cap from refrigerator was complicated by the adjustable temperature control - it is loosely attached at the back of end cap and also has to be removed to get cap out. Gentle persuasion accomplishes this. Getting the slider off end cap also a bit difficult. Then I removed the drawer glides. Reversing all steps was fairly easy and the rest of the "fix" went well. I wished that there had been some written directions - or at the very least, a diagram of how all went together. All in all was still cheaper than repair person.

It was easier than I had anticipated. Just had to make sure that I was very careful in removing the old part so I did not break any of the good plastic that I needed in order to install the plastic temperature control to the new part.

I removed and replaced the right pantry end cap, as well as the drawer lid.

Took bottom 2 shelves out. 2 screws held assembly in to main cabin. Remove them then 2 additional screws held drawer bracket in place. Easy yet patience and finesse is needed

Removed the food bins and lower shelf. Unscrewed the end cap. Removed the drawer hinge. Re-installed hing on new end cap. Installed the new end cap. Re-installed drawers and shelf. DONE!

Great graphics on the website helped to correctly idenitfy the required part. Part arrived quickly and well packed. One of the easiest transactions ever!

Simply fit the frame onto the back piece and lined up all of the anchoring plastic hooks to reattach. I had some minor difficulty in navigating the website but the customer service agent was very helpful and assisted me in purchasing the correct part. Thanks! Gretchen

Replaced the control board. Called another web site and for $15 got the twelve step code to set the new control board.

Still no cooling. Same issue as before.

Sears coming again tomorrow to try again.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

It took longer to empty the items off the shelf than it did to do the repair. Slid the veg, drawers out, set them aside.Took glass shelf out set it aside. removed three screws with 1/4in socket. Removed end cap. replaced with new end cap, replaced screws, cleaned and replaced shelf and drawers. Was a very easy task. these pegs break very easy, this is the second time I have had to replace the end cap, both times it was the left size. problem is you have to buy both the left and the right side together,

took out old lid, took out drawers above this drawer to make it easier to work on. installed new drawer simple by hand with no tools. put other drawers back. very simple no tools needed.

Removed glass shelf and inserted plastic running bar for drawers

An ideal opportunity to clean the tracks for the glass top and sides. I just removed the two (2) screws with nut driver and gently eased the end cap off by slightly pulling it forward and up, inserting the lid onto the new endcap and slipping the cap back into place securing with the two screws. as easy as pie. I did not change the right end cap as there was no need for it, But if U have to change it U must also first disconnect the back plate.

Just removed drawers and glass plate. Put in divider and replaced drawers and glass plate. I was done in 5 minutes. no tools required.

Pulled old gasket off door put new one in channel on door pushed gasket in channel less than 10 minutes