All Installation Instructions for Kenmore Refrigerator 59675969700

Broken clips on old part

Snapped in new part

Parts Used:

Damper Cover Insert

Rose from OCOEE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped making ice

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Parts Used:

Replacement Ice Maker

Daniel from DAVISBURG, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Cracked handle

Unscrew old one replaced with new one

Parts Used:

Freezer Door Handle

cheryl from WANAQUE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken center crisper rail

Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.

Parts Used:

Refrigerator Center Crisper Drawer Slide Rail - White

Allan from Tucson, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broke the Rocker Switch in Fridge side

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Parts Used:

Door Switch

Sung-Su from BISMARCK, ND
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker not producing ice

The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...

Parts Used:

Ice Maker Wire Harness

frank from NORTHRIDGE, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Raplaced switch

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Parts Used:

Refrigerator Door Switch

Winston A from Brooklyn, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Center Crisper Rail Broke Off At One End--Drawers Would Not Slide And Hang Right.

Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!

Parts Used:

Refrigerator Center Crisper Drawer Slide Rail - White

DANA from ASHTABULA, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Fill cup broke.

Very easy to order from parts select. Took seconds to replace.

Parts Used:

Refrigerator Water Fill Cup & Bearing

Aliki from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped functioning

Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.

Parts Used:

Replacement Ice Maker

richard from colorado springs, CO
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped working

After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.

Parts Used:

Replacement Ice Maker

Raymond from Panama City Beach, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Parts Used:

Refrigerator Door Switch