59669984001 Kenmore Refrigerator - Instructions

Followed easy instruction video. It was like new in fifteen minutes.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Dropped down the front control panel were you program the the tempertures when you open the doors. This just pops down from the front. Then change out the printed cicuit broad two wires all done.

Removed back cover. Removed fan with mount which was a little difficult. Installed new pan and parts that were removed. Part came in one day. Great service.

This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!

Unplug the refrigerator and pull it out so you can work behind it.I had to get a helper to lean the refrigerator forward and let it rest on a towel I placed on the countertop. The tray was underneath the refrigerator near the back so I leaned it forward enough to remove the metal plate that holds the tray in place. I placed a scotch behind the front wheels to keep it from rolling backward off the counter it was resting on. I had to remove the cover from the unit on the lower back side of the refrigerator to see how the tray was moumted. Once you remove the plate you have to slide the fan off the tray and then you can remove the tray. Simply reverse the whole process to install the new tray, upright the refrigerator and plug it back in to the outlet.

Refrigerator completely quit due to suspected power surge as a result of daily afternoon thunderstorms. Quit means compressor would not run, LED temperature controls would not light, but fan continued working. First, replaced Start Relay & Capacitor located attached to compressor. This was successful and compressor immediately started. However, Refrigerator controls at Electronic Control Board (ECB)failed to light up indicating no control over over unit. Replaced ECB and unit lit up and control established. The Start Relay & Capacitor are slightly difficult to find as they are black in color and merge into the base of the compressor. It helps to be flexible to remove and replace this unit due to it's difficult location. The ECB is easy to access as it is top inside front behind lights of unit. Plastic housing simply unsnaps for easy removal. Instructions do not tell you to make sure that you re-install the upper narrower control board with press pins toward outside of control face. A simple item but easily overlooked as one has to "pull" at the connecting cable of the two control boards. Success finally after three days. Parts Select was great and item shipped quickly. As a contractor, one can usually figure cost of job at three times the cost of the part. This repair would have approached $600. Cost of parts was $200. Savings were substantial and would recommend DIY provided you have time.

Thanks for the control board. However, it arrived in two days not overnight, UPS noted on their tracking site the error was their own. Also, the part did not come with installation instructions or programming instructions. Found on youtube a video that described in detail the programming procedure: . . . . . very helpful.

Thanks,
Marc

Temp in fridge stayed around 45-46 degrees even at lowest setting. First went with most probable problem of replacing the Evaporator Motor Kit in lower freezer compartment, no change, next ordered thermistor in fridge area, no change, temp stayed in same range, then tried the Electronic Control Board in top of fridge, fridge works like a charm now. Very easy repair, just follow directions to progam new board. Possible cause a lightning strike near house that fried a TV about 2 years ago - fridge began to freeze items at first and went downhill from there.

I was so happy to find that i could order the part online and not have to call a repairman and pay for a service call. The prat shipped in one day! It was very easy to install. Only tip i will give is, make sure you put it in the right direction. If placed in wrong the drawers won't open.

Followed instructions supplied on Your website. Instuctions were well explained and easy to follow.

I watch a widea on part select 'how to do that' and was relly very easy to repleace a part. The delivery was next day. They are triting customers very serious and professionals. I'll recomended part select for all my friedds with similar problems. Thank you.

It was so simple! Removed the glass shelf that sits atop the vegetable bins, inserted the center crisper rail, put the glass shelf back on top of it and replaced the vegetable bins. I loved that I didn't have to bother my husband to do it! Very happy at how fast the part came after I ordered it.

remove crisper baskets. Remove glass shelf above baskets. remove broken rail note front and back end of rail. Place new rail with same orientation as old rail. Very easy repair.

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.