All Installation Instructions for Kenmore Refrigerator 59669282001

Broken basket hanger

It was easy, remove clips and install new basket hanger and then just clip on the clips.

Parts Used:

Bracket - Right Side

Mark from Chelmsford, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Freezer occasionally had a temperature alarm.Clicking noise also.

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Parts Used:

Refrigerator Capacitor

Barry from FORD CITY, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Plugged it in.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Parts Used:

Refrigerator Capacitor

Adam from GLOVERSVILLE, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

old one broke

snap the new one in place.

Parts Used:

Refrigerator Toe Kick Plate (White)

john from CASCADE, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken center crisper rail

Lift off glass shelf and insert tabs of rail on each end , replace shelf.

Parts Used:

Refrigerator Center Crisper Drawer Slide Rail - White

Neil from WILMINGTON, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Refrigerator was not cold.

Refrigerator was not cold.

I had this problem before and it was the control vale in the back of the refrigerator. I ordered it and change that out in 5 minutes. That wasn’t the problem. I had the repairman come over and within 5 minutes he told me what the problem was. He showed me where the control board was. He then walked me through the removal process.

First remove the light cover on the Freezer & Refrigerator in front where the light button is located. Pull down on the front of the light cover. It pops out.

Second, in the front of the freezer & refrigerator temp control panel put your fingertips in front of the panel and pull down it’s hard to get the pins to release but the front pins will release, then pull down a little to allow the back hooks to release. (You can use a small common screwdriver if you can’t get it with your fingertips).

Next, once the panel is removed then disconnect the wiring harness. Then bring the panel to the counter, this is where you remove the circuit card and replace it. There are 4 hooks that hold the circuit board in place. Use a small common screwdriver to push the hooks away from the board. The new board comes as one piece. The board is perforated to allow you to snap the board. Directions come with the board and how to snap it. You will need to pay attention on how you removed the board. You will need to put the new board in the same way it came out.

Once the board is re-installed and lock into position reverse the process and install the control panel back into position.

Next is the programing of the board. Follow the directions that come with the control board and you will be back in business

This task took about 15 minutes to remove & replace and to program.

Parts Used:

Refrigerator Electronic Control Board

Edward from Reading, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The control indicators would flash and buzzing noise came from the controler

Followed the video exactly as shown from the website. I do suggest using a mirror or your phone to visualize the notch to press to drop the cover.

Parts Used:

Refrigerator Electronic Control Board

John from JACKSON, MS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

compressor not running

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

Parts Used:

Refrigerator Capacitor

Doug from Lancaster, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

None

Just put it into the bottom of the fridge and it snapped into place. NO PROBLEM AT ALL.

Parts Used:

Refrigerator Toe Kick Plate (White)

Victoria F, from NEWARK, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

No cold

Like you video

Parts Used:

Refrigerator Capacitor

Jacqueline from LEXINGTON PK, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

Parts Used:

Condenser Fan Motor

John from PHOENIX, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Noisy, running constantly motor in damper unit.

Unsnapped and pulled off small cover exsposing two phillips head screws. I removed larger cover and styrofoam insert fully exsposing the damper unit. i unplugged same and with a 1/2 inch wood chisel was able to release the "snaps" holding the old unit in place. Simply reverse procedure to install new unit.

Parts Used:

Refrigerator Damper Control Assembly

lawrence from TRAVERSE CITY, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken glass crisper -shelving

The glass shelf sits on top of the crisper housing. That was the problem since when I turned the housing over to clean, the glass fell off. I just had to set the new part on to the housing and it was fixed.
I do want to comment on how easy it was to find the part on your website, how reasonable the price and the quick delivery. Thanks!

Parts Used:

Refrigerator Crisper Glass

Sonny from Moraga, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

freezer and refrigerator compartments not cold enough

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Parts Used:

Refrigerator Capacitor