59668042802 Kenmore Refrigerator - Instructions

Snapped old one off, snapped new one on

Removed the glass shelf, position the rail in its slots and replaced the glass shelves.

Removed both crispers and shelf . Inserted new rail as explained in video. Replaced everything.

Followed easy instruction video. It was like new in fifteen minutes.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed back cover. Removed fan with mount which was a little difficult. Installed new pan and parts that were removed. Part came in one day. Great service.

Found instructions on You Tube how to replace Jazz P/C Board Replaced board and manually defrosted evaporator coil.Everything seems to be working fine

Dropped down the front control panel were you program the the tempertures when you open the doors. This just pops down from the front. Then change out the printed cicuit broad two wires all done.

This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!

first unplug unit, remove clear light cover it snaps out. there are 2 slots on either side of the light housing stick the screw driver in the slot and push the tab and pull down this will unlatch the control board housing, remove the board socket plugs, and the board from the frame, on the new board you will have to snap the PC board at the pre indented line. replace in reverse and follow instruction to program the code.

The unit has two fans on it. One is located in the back and the other is locate inside the freezer section behind the panel. Remove the four bolts holding the door to the sliding rack. Remove the ice machine. Remove the back panel. Noticed that the fan was covered in ice thus shorting the fan motor. Tested for voltage to the fan was good. Replaced evaporator fan motor and unit works perfectly

Unplug the refrigerator and pull it out so you can work behind it.I had to get a helper to lean the refrigerator forward and let it rest on a towel I placed on the countertop. The tray was underneath the refrigerator near the back so I leaned it forward enough to remove the metal plate that holds the tray in place. I placed a scotch behind the front wheels to keep it from rolling backward off the counter it was resting on. I had to remove the cover from the unit on the lower back side of the refrigerator to see how the tray was moumted. Once you remove the plate you have to slide the fan off the tray and then you can remove the tray. Simply reverse the whole process to install the new tray, upright the refrigerator and plug it back in to the outlet.

Replaced the CNTRL-ELEC board with ease. Just slide back and remove the light cover. Use flat tip screw driver to release and drop down unit. Remove connectors and attach to new board after breaking in half to fit same as old one. Programming is easy, just look at the CODE on the name plate inside the door. Mine is 0-1. Follow procedure of holding the light switch off while touching the freezer control 3 times within 10 seconds. A "P" for programming will appear. Still holding the light switch, touch the refrig control to set for your code. Freezer button says 0, refrig button says 1. When you release the light switch, the programming is done. Mine starts out with a 4-4. It is now working quieter than when it was new and is very cold again.

Found troubleshooting steps for control board (called a jazz board) and ran through the steps. Found the control board (jazz board) was bad. Pull front vent cover where the condenser is off, you will find manufacture manual papers for these steps and for programming of new control board (don't lose these papers for next time). Papers are located under bottom of front right corner of refrig where they are in a bag ( cut bag open and replace back when finished for next time). Replaced board by: 1. Pushing light cover to back to remove 2. Take screwdriver and push on two tabs that hold housing on at each side (will see two holes where they are by looking from behind, with your head inside) push and pull down. There it is 3. Replace board with the tabs that hold it in. (use latex gloves and only touch outside of board, to avoid static electricity to the board. 4. Reinstall and program (Code for your refrig is on cabinet sticker where model and serial no. are) 5. Install a surge protector on the plug for possible surges. Not too bad to install, just finding how it comes out .

Followed instructions supplied on Your website. Instuctions were well explained and easy to follow.