59666132703 Kenmore Refrigerator - Instructions

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Let the ice in the freezer melt while installing P trap drain tube

Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.

Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.

It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required

got the new part, took the old part out and snapped the new part in! Very easy. Thank you.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

The fridge would occasionally run warm, requiring me to turn it off and defrost the evap coils in the freezer. I found an online video that demonstrated the entire process of replacing the control board. The fridge model in the video was different than mine, so it took some time to figure out how to remove the panel. Once that was done, the rest was easy. The only tool required was a flat-head screwdriver that was used to push in the tabs holding the panel in place. The circuit board took more effort to split in two than I had realized, and I had to be careful not to bend any of the components on its surface. The whole process took less than 30 minutes, and the fridge is working properly now..

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

Used UTube directions the ones that came w/part we're too generic

Removed & Replaced

I checked the element and the thermostat and determined the problem to be the control board. I simply followed the instruction in the video. Everything went well until the last step, the video said to push the freezer down button. When this did not work I refered to the written instructions which told me to push the up button. That did it. Job complete. The unit is working as it should.