59666032702 Kenmore Refrigerator - Instructions

Followed easy instruction video. It was like new in fifteen minutes.

Removed the glass shelf, position the rail in its slots and replaced the glass shelves.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Unplug the refrigerator and pull it out so you can work behind it.I had to get a helper to lean the refrigerator forward and let it rest on a towel I placed on the countertop. The tray was underneath the refrigerator near the back so I leaned it forward enough to remove the metal plate that holds the tray in place. I placed a scotch behind the front wheels to keep it from rolling backward off the counter it was resting on. I had to remove the cover from the unit on the lower back side of the refrigerator to see how the tray was moumted. Once you remove the plate you have to slide the fan off the tray and then you can remove the tray. Simply reverse the whole process to install the new tray, upright the refrigerator and plug it back in to the outlet.

Dropped down the front control panel were you program the the tempertures when you open the doors. This just pops down from the front. Then change out the printed cicuit broad two wires all done.

Found instructions on You Tube how to replace Jazz P/C Board Replaced board and manually defrosted evaporator coil.Everything seems to be working fine

This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!

Replaced door closer part on hinge. Did not fix problem. Be sure to order mating bushing that goes in the bottom of the door . Part #67004977

The instruction video was so helpful. I watched it before I ordered the part to be sure I was able to make the repair. The replacement part arrived quicker than I expected. Cleaning the shelf & bins was the most time consuming part of the job. The replacement part fit in place perfectly. My fridge is good as new again!

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

Noted the Damper Assemby in the upper rear of refrig section,was always staying open during checks for problems. Controls appeared to be controlling temp changes when adjusted. Pulled the damper assemby after removing two screws holding the diffuser/cover(diffuser pops off with screwdriver) Damper assembly snaps out , unplug wires, snap new damper assembly in place, reconnect wires at the plug, replace cover with foam insulation, secure with screws replace diffuser snaping in place. Recheck settings for desired temperatures.

Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!

Found Board location and replacement instructions on Appliance Doctor website. Price there was actually 3 $30.00 cheaper.Had to remove light cover to access slots to insert a flat blade screwdriver which you use to depress tabs to unlock control board housing. It then swings down so you can unplug wiring harness's and remove and replace control board. Too early to tell if defrost is working yet.

I popped out the electronic control board and replaced it with the new one. After following the programming instructions provided with the part, the refrigerator/freezer worked great.

I used an internet link that the customer service lady provided to assist me in learning the proper removal method, so I could replace the part. So far this seems to have fixed the problem.