59652672200 Kenmore Refrigerator - Instructions

I found that the evaperator coil was freezing up solid, not allowing air flow. Something was wrong in the defrost circuit. After troubleshooting, I found that the defrost timer was okay, as well as the fan. The only thing left was the temperature switch (thermostat). I found the part online for a reasonable price and ordered it. The part actually came the next day, I was amazed. I removed the old part by cutting the wires. Then I snapped in the new thermostat and crimped the wires back together (color-matched). It was that easy and I saved myself hundreds of dollars. Great service!

Simply cut the water tube on both sides of connector and push in the new one.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Unplugged refrigerator.
Removed water drip tray.
Removed two Phillips screws.
used putty knife to
get behind outer plate and popped it off.
Disconnected electrical connections.
Removed the 4 nut driver screws.
removed ice maker door.
Removed seal around old Ice shoot flap and cleaned.
Removed insulator pad from old ice maker flap and cleaned.
Installed seal and insulator pad on the new chute door.
clipped new chute door intact with seal and pad in place and snapped the top clips into place.

Reversed procedure to reinstall refrigerator parts.

Plugged in refrigerator and tested. Had no issues.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Refer to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!

Remove two screws from top door hinge.
Remove door from unit
Remove old broken plastic cam 1 screw
Replace new door cam tighten 1 screw
Reinstall door and top hinge screws.

I removed the two screws on the Ice dispenser housing and dropped it down. I catalogued all the electrical connections on a piece of paper for reassembly and basically followed my nose. I gave my wife the honor of testing it and I held my breath. Replacing this part was a breeze and it functioned perfectly when the job was completed. I wish I had done this three years ago when it failed! Thanks very much !!

I had to order three times before I got the right part. This was due to my rush to fix the problem and not studing the diagram carefully (black and white diagrams are not that clear). The repair was very simple. Just remove the rubber from the plastic door and slip on the new one.

remove the back plate, removed the screw holding the valve, removed electrical wires and water tubing. installed new valve. very simple. also i received the valve in one day. thank you

Very easy to order from parts select. Took seconds to replace.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Super easy - emptied door of all food, unscrewed bracket from top of door, lifted door off and set aside. Broken cam removed, new one screwed in, and lubed with some Vaseline. Set door back in new cam, screwed bracket into the top, and good to go. I was kinda worried about shopping from PartSelect since I had never heard about them, but the part was here in less than 2 days. Pretty awesome little company.

Removed all the food from the freezer. Removed 5 screws that hold the back cover on and removed the cover. Melted the build up of ice that was present on the coils and other components behind the cover. I was sure to keep a towel under the fridge as the drip tray was sure to over fill. With the fridge unplugged, cut the wires from the thermostat. On the wiring side, not the thermostat side, shorted the wires I just cut together and plugged in the fridge. The defrost heater turned on. This told me that it was indeed the termostat and not the timer. Replaced the thermostat and it has been runing ever since.

replaced the entire ice make - 3 screws and a squeeze -off connector and it's out. Reverse to re-install... except that the fill tube had iced up. To thaw the fill tube: unload freezer section (leave food in fridge, but keep door closed), remove ice maker. Boil water, dip drill bit (dull end) into hot water, swirl around, insert (dull end) into to fill tube. Depending on how hot you got it, maybe a tablespoon of ice will melt. Repeat many times - fill tube is about 14" long! Do not use anything sharp - you will nick the tube and ice will form causing you to repeat this procedure. Do not try to break the ice - let the heat work. It took me about 30 minutes to thaw the whole thing - it made a nive gasping noise when the final plug opened up. Re-install ice maker.