58RI Whirlpool Refrigerator - Instructions

easy as pie everthing good thanks

My husband had taken the ice maker out and deceide which part we would need to fix the maker. your online parts list made this possible. The service you provide was most helpful. The shippment got it to us in record time.

Disconnect power cord turn off water supply. Remove four screws on bottom of ice maker unit.Then look for locking clips on bottom of @ near supports and remove unit sliding & cocking until you can turn motor toward you cord is just long enough pry motor control off with hand or flat blade screw driver buy pressing on side edges.Remove motor from unit by removing three screws & pull out of plug on one corner. [side by side unit not freezer over fridge like video].

removed cover, removed (1) screw that holds unit in place, disconnected power connectors, removed (3) screws that held assembly together, attached new part with (3) screws, re-installed unit.

After determining that the gear on the motor assembly had broken off, I ordered from this website. First time using Partselect, and will now always check and hopefully order here first. Repair was very easy. Pulled the old assembly off by taking out three screws, removed the broken assembly, put the new one on, replaced the three screws, and installed the icemaker back into the freezer. Took a about 30 min total. Came back in about an hour and had ice!

This is the 4th motor on this ice maker. Sears replaced the original motor at a cost of >$300 and this is the 2nd motor I have replaced at a cost <$70.
Repair is quite easy since this was the As described on your site, simply remove the door flap, remove the covering for the wiring, remove 3 hex nuts under the floor of the unit and the entire ice maker slides out. After disconneting the wires, you simply slide the cover from the motor, remove 3 philips screws and slide the old motor out.
Align the new motor, slide in, replace 3 philips and reverse the process to place the ice maker and hex nuts.
Was "back in ice" within an hour or so.
Thanks for the instructions and video and for making the parts affordable for do-it-yourselfers!

Remove tray that held ice then took off cover to the moter.removed three sewes that moter came off .then put on new one

Placed ice maker control switch to OFF position. Removed wiring connection cover from ice maker. Disconnected wiring harness from ice maker. Removed old ice maker control and motor by removing motor cover and three screws. Installed new ice maker control and motor with the three screws and cover. Reconnected wiring harness and wiring connection cover. Placed ice maker control switch back to ON position.

This repair was so easy I can not believe I waited so long to do it. What was I thinking?

exactly like the video clip that the website had for the part - very easy!!

1/4 nut driver removed 3 screws and unpluged connector at which point you can remove the entire ice maker assembly. Once it was out there was three philips screws that removed the head unit (after the fact I think I could have left the assembly in and just removed the head unit) replace old head unit with new one, making sure to aline the flip bar in the slot. Slide right in and had ice later that night. A very simple fix that once again made me look like the husbandly hero that we all strive for.

No ice means motor and assembly 60% of the time. The hard thing was to unplug the wire plug to the refrigerator from the icemaker and to reconnect it. Its fixed for another ten years. Ez

Removed the single screw holding the ice maker in Place and unlugged wire ,then removed cover off of the end of ice maker and the three screws holding the actuator onto ice maker and installed new one. Reinstall ice maker......works great

My son's ice maker quit over 5 yrs ago. Repairman told him he would need whole unit.
I keep trying to fine the "whole unit". I finally wnet on to the part list and decided
it was probably the Modue assembly. I odereded it and guess what!!!! That was it....a $66 part!
It is working fine now!!

I actually went on your website and used the do it yourself repair video as a step by step guide to complete the repair. It was as easy in real life as it was presented on the video. I will use this website to buy and repair future issues I may face with my appiances.