58716074200 Kenmore Dishwasher - Instructions

First, I had to remove a small metal paper clip that somehow ended up in the bottom of the dishwasher, which jammed the spray arm. The spray arm wasn't able to spin around, so it melted onto the heater. I removed the spray arm, and replaced it with the new one.

I pulled off the cover inside the sump area. Then pulled the washer out from the counter and turned it on it's side. I took the old pump out and crimped a new wire harness on. It was a simple repair for a DIYer.

Before pushing the dishwasher back, I tested the dishwasher with it pulled out from the counter. It was easy to see water was flowing forcefully through the upper tubing now. Success.

Troubleshooting this faulty pump was harder because it was functioning, but it did not have enough force to push the water up to the top rack. I convinced myself that the pump was the problem by plugging the lower rack with a cork. The spray was still too weak to rotate the upper spray arm. I also ruled out the timer with a stop watch. This unit alternates upper and lower racks by pausing either 0.6 seconds or 3 seconds. This controlls a ball that diverts water to the upper or lower rack.

Thought the problem was a faulty door gasket (there was a gap in the middle of it) so I ordered new(new one had a gap also) replaced it anyway - maybe it was worn out? Still leaked! Had to sit and stare at it and cycle it through. finally realized the spray arm had a hole in the end that was spraying directly into the gap in the door gasket. Hot glued the hole and it stopped so I bought a new spray arm - no leaky!

First I just rolled out the lower rack assembly, and rolled the new one in. Then I moved onto the upper rack. I started by sliding the off the rail cap lock at the end of the rack. The entire cap does not come off, just the bottom slotted piece. This is done by simply edging out the bottom of the cap, toward the front of the dishwasher, until the bottom slides out of the slot, and lifts out of the way. Then the upper rack was released to roll freely out of the support rail. The next step was to pry off the top of the water diverter. Next was to unscrew the wand assembly from the water diverter that is attached to the upper rack assembly. There are no water lines attached to this, it just directs the jetted water from the top of the dishwasher. Then simply pop the mount from the upper rack. And reassemble the way it came off. This was a simple fix to make the dishwasher like new inside again. The racks purchased from Parts Select fit perfectly with no modifications or trouble. This operation took less than ten minutes. Anyone should be able to handle this operation. If you are afraid to disassemble the upper rack, take a few digital pictures to refer to, and delete them later. This is a tip that has been priceless to me in the past on other projects. Thank you Parts Select.

It took less than a minute to remove the old bottom door gasket - it pulls right out. You wouldn't think the part looks the way it does (a 1.5 inch wide plastic strip that runs the length of the door with rubber gaskets on both ends) but have faith. Trust the diagram/picture - it is the correct part and will fix the leak. The new gasket arrived within a couple days of ordering and was simple to install - no tools. It slides into place in less than a minute and is held in by friction. Problem solved and no more leaks. For under $12 (parts and shipping) I had my dishwasher fixed. A service call by itself would have run $75 - just for someone to show up at the house, and then probably another $50 for parts and labor to install. My wife made the comment "Even I could have fixed that". A very simple and easy repair - you can do it!!!

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman

Unplugged dishwasher, pulled it out. Unclamped hose and unscrewed water source to inlet valve, removed wiring harness, unscrewed bracket and reinstalled new valve. Now have a functioning dishwasher.

The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strainer basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!

This was right before T'Giving. Ordered the part Wed, and it arrived on Sat morning. I had read the other comments, so thanks to the person who said to make sure you snap the new one in place and check for a snug fit, the replacement was in and working in no time at all.

Alighned the bracket and pushed in.

One Roller detatched and hit the heat coil and melted. Both of the Spring Linkages borke. It's was quite obvious they were made not to last long. My Husband did the repairs. Thank you for asking.

First unplug the unit.

Second remove the kickplate. When you do this pay attention to the position of the insulation panel. It is confusing as to how it is put back together. Simple if you see how it comes apart.

Third unsrew the screws that hold dishwasher in palce under the counter top.

Genly pull the appliance from under the counter top. Understand the copper piping connected to the unit for water will only allow you to pull it out a few inches. Otherwise you would have to turn off and disconnect the water supply.

Reinstall the plastic clipsand springs. There are several holes in the frame of the dishwasher where the springs will attach. The further back you attach them, the more tension will be applied to the springs. This part of the operation is somewhat trying as you have limited visibility and access.

When springs and clips are installed, test door, slide unit back in place, reattach kickplate and insulation panel and then reattach to countertop.

All in all relatively simple and doable. If I had any problem it wasnot paying attention to how the insulation panel and kickplate came apart. No big deal.

Disconnected power to the unit at the circuit breaker. Removed the bottom panel of the dishwasher. Used a stubby Phillip screwdriver to remove the single retaining screw holding the high limit thermostat against the bottom of the dishwasher tub. Not only was the thermostat burned out, one of it's electrical connectors was also destroyed. Removed the tape holding the cable bundle together so that I could work on the quick disconnect plug outside of the unit. One end of the quick disconnect plug was completely burned through and needed to be replaced. After doing the necessary electrical repairs and assembling the new thermostat into position I applied power and everything worked fine. It helped having a picture on your website that I could use to identify the correct replacement part.

I will make a few additions to the other instructions, which are great and let me see that the job was doable. To the tools needed, add pipe tape.
1. Shut off water supply.
2. Removed inlet water hose where it connects to the valve assembly. (This was a pain on my machine—too little room for the wrench, you may have a better tool—but I did get it out, slowly.)
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection (Look for your red and blue wires on the connector, my red was to the top of the solenoid, and reattach with the same grounding) from the solenoid. (This step was a great bit of information; It allowed me to see that I could do the following steps with ease, That is, the unit dropped down where you could work on it.)
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical connection to new valve solenoid.
6. Remounted assembly to the frame.
7. Re-attached the inlet water hose to the hose adapter connection on the valve. (I had to take off the L shaped connector at the bottom of the old valve and add it to the new valve. This was an extra step that required two bigger wrenches to hold the old assembly and unscrew the L joint. I just needed the extra leverage to get the old off and the new on. I am referring to the copper connection that connects to you water supply)
(8) The new valve had a slightly different configuration than my old. The rack it sits on was about an inch or so longer. This meant that I had to readjust my copper pipe just a bit to match up when it was reassembled. No big deal, I had lots of pipe length to work with. Actually, moving the valve a bit further back made more room for the wrench to work—very happy about that. In addition, the hose attachment went from a left exit to a back exit. Doesn’t seem to matter.
(9) Turned on the water, washed some dishes. (Took me about an hour, mostly because of the difficulty with the wrenches. Otherwise—piece of cake)