58715202801 Kenmore Dishwasher - Instructions

You tube video and it was so easy less than 20min had it fix

I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.

Pull out shut off power unscrewed fan.Replaced with new fan . Rest power and shoved back in ran cycle. All was fine

The drain pump was making a high pitched buzzing noise which told us that its days were numbered. When I ordered the pump I found out that the dishwasher was really made by Electrolux for Whirlpool. Taking the pump off was a simple matter of removing two hose clamps and prying the pump off the frame. The hard part was realizing that it just pulled off without damaging anything. The new pump easily slipped right in and the screw in hose clamp was easily installed. However, the hose clamp that required pinching with the pliers was not that easy. I had to use a screwdriver to push it all the way on while holding the clamp open with the pliers. All in all pretty easy.

Followed the instructions given on the video, for replacing the drain pump. I did not pull the unit all the way out of the counter space just pulled it out about a foot. I had to lie on the floor to change the pump. That cost me some time for removal and installation, but I did not have to disconnect any water or electrical lines. I did unplug the power. The exchange went smoothly accept for the one spring clamp. Hard to squeeze and slip on. Would have been better to use a different kind of clamp. I have arthritis so that was an issue. All in all a good experience. A Big Thank You !! to this site . There instructions were perfect, the site is very user friendly. They saved me the cost of hiring a repair person. I'm a 75 yr. old disabled female, if I can do it then you surely can.

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.

Removed front panel of door, to get to the screws that hold the door on the hinges. Removed door, pulled gasket with pliers from bottom of door, not easy to get out because of mineral deposits. Had to push quite hard to get new gasket in. Put every thing back together and no leaks. I live in Alaska and I tried to order the part through Sears and they wanted $18.95 for shipping for a $12.87 part. The part with PartSelect was $14.92 but only $6.95 for shipping. I ordered the part on a Tuesday and recevied it on that Friday. We in Alaska get very tired of companies thinking we live on another planet. Thank you PartSelect.

Had trouble installing the new gasket at first. Fell inside the door, and would not stay in the groove intended for it. After watching the video on your website, learned is best to angle the gasket and work in slowly to the groove from one side. Much easier then

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

Simply pulled old gasket out with hand, and slid the new one in place!

Remove kick plate. Pump is right up front. Disconnect the two wire from the pump. MAKE sure u have removed all water from dishwasher! There will be a little left in the pump but nothing to worry about. Next on the top of the pump there is a hose clamp. Loosen it and remove the hose. Now use pliers to slide the hose clamp off the lower hose that hooks to the dishwaher. Use a flat head screw driver to push the tabs on the white clip over and pull off the pump. Now just do this in the reverse order. Approx time: 10 minutes

1-2-3. Finished ! I had watched your video on how to !

I followed directions from a video on this site and written directions in order to make the repairs. Pulled out the old gasket from one end with pliers . I cleaned out the slot in the door of any food or dirt and replaced with the new gasket. It was a very easy and quick repair that allowed me to use my dishwasher quickly. Thanks for the help.