58715074200 Kenmore Dishwasher - Instructions

It is rather easy to repair. After you remove the screws that secure the top of the dishwasher to the countertop you can slide the disherwasher out far enough to gain access to the hose. The hose pulls off after you slide the spring clips down the hose far enough so they no longer grab. Then simply reverse the order and you're done. Less than 30 minutes and you should no longer have to hand wash your dishes!

I went to your website found part# and parts diagram and ordered parts . I picked standard shipping . That evening e-mailed me they were instock and shipped also gave tracking # thet parts were here the next day.I removed the front dec panel then the 4 nut& bolts holding door to hinges(with door in closed position).Then I removed the 2 screws holding the hinges to the frame/axle. Replaced hinges with new ones .Put screws back in frame/axle . Put 4 nut and bolts back to secure door to hinges . Then i reinstalled under counter put new wheels on lower rack . I then filled it with dishes and ran a long cycle checked for leaks THEIR WERE NONE!!! THANK GOD !! Job complete, Thanks parts direct for a well designed website and detailed pics and parts#. TIM

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to sump pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

slide out dishwasher. remove 2 screws holding motor/pump assembly in. slide out motor/pump bracket. disconnect electrical connection from motor. pull motor/pump assembly out. install new 'O' rings on new motor/pump assembly. (lube with liquid soap). install assembly. slide in motor clamp and install 2 screws. reinstall dishwasher. run test cycle. Fixed!!

Manually took off melted parts and replaced them with the new ones.

Removed the two bracket screws attaching the washer to the countertop, and removed the kick panel beneath the door. Pulled the washer out enough to access the spring arms. Replaced the broken spring arms, and pushed the washer back into it's space, re-attaching the kick plate, and securing the lock tabs on top of the washer. Used one phillips screwdriver, a #2 tip. That simple.

replaced with new lower rack, out with the old, in with the new! Shipping was great new part arrived in 2 days! Great service, and will use again for all parts needed in the future, and will tell everyone about this site! Thanks a bunch!

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

Took off front door panel with two screws. Found the part in the door. took it out and slide the new part in. My husband screwed the screws while I held the door in place. If I had known it was so easy to do I would have done it as soon as I got the part but I waited for my husbands help.

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

pulled DW out from under counter. drained water from unit. laid DW on its side. removed 5 screws from unit 2 to remove drain motor and three to remove bracket. used adj pliers to remove spring clamp and screwdriver to remove other clamp. to install i did the reverse

Our dishwasher handle was broken and I stumbled upon PartSelect's YouTube video that described how to change the Latch Assembly while looking for a new dishwasher. It looked easy so I thought that I would give it a try. The hardest part of the installation was finding which circuit breaker shut off the dishwasher. That being said, our dishwasher was slightly different from the model shown in the video. When we unscrewed the screws on the inside of the door the top part of our dishwasher did not come off and fall forward as it did in the video. Our control panel was longer and continued beneath the front panel. We could not access the latch assembly until we removed two small screws near the bottom of the dishwasher door and popped the front panel off. Other than that it was exactly as the video showed. EXCELLENT service. I ordered the part and received it the next day. WOW. I would recommend this website to anyone who needs appliance parts.

My upper spray arm attaches to the upper dish rack. It comes in four parts: the spray arm, the bracket which attaches it to the rack, the water funnel, and a plastic nut that holds the pieces together. The nut was worn and wouldn't hold so I replaced that piece and it works great. It took less than one minute to fix.