58714852200 Kenmore Dishwasher - Instructions

Lower the door and remove bottom dish tray. Feel with fingers the area where gasket will be pulled from (just below bottom door edge) Pull old gasket from door edge into direction of inside dishwasher. Insert new one in same orientation as old (small slit to right side). New gasket strip will seat into door bottom.

After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

Pulled the dishwasher out from under the ounter, laid it flat on the front side, unplugged the motor, removed two screws and the retaining clip, pulled the motor straight out, oiled and put the new o-rings on the new motor, slid it in, replaced the clip and two screws, reinstalled the dishwasher, and done.

My upper spray arm attaches to the upper dish rack. It comes in four parts: the spray arm, the bracket which attaches it to the rack, the water funnel, and a plastic nut that holds the pieces together. The nut was worn and wouldn't hold so I replaced that piece and it works great. It took less than one minute to fix.

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Internet search found high limit switch as primary failure, removed dishwasher existing part looked new, no signs of wear as was expected. Second failure was the heating element, I ordered the part; At the same time I found a random youtube video, that had me check the continuity of the heater and tested good. Then the video indicated the heater relay may have one leg that has lost the solder and stops the heater element from working. I took the control panel a part and the heater relay had the same failure, one leg had a missing solder joint. Using some flux, solder and soldering iron I repaired the connection and added some addition solder to the circuit. Reassembled and the dishwasher is heating as it was before everything is working as expected!
(P.S. The heater relay failure appears to be a common problem, but the actual root cause [relay failure due to poor solder joint] is never reported back to the company, they just hear the heater element stopped working and they never fix the real issue because the customers are throwing out the dishwasher, when it could have been repaired with a simple fix. More importantly it should be something that is investigated as it may needs an engineering redesign. but can't fix what you don't know about or fail to investigate. I did purchase a new relay to replace the existing one, to be installed upon arrival).
Once again a random youtube video identifies and resolves a problem, that would have had me purchasing a new dishwasher, and maybe this is all planned engineering obsolescence.
When will get smart dishwasher that have sensors or at least codes that report the failures correctly, to make DIY repairs?

Both the door latch assembly and strike broke on the dishwasher. I was happy to find both parts available at PartSelect.com. Simply removed mounting screws so I could pull the dishwasher out, removed the old strike, disconnected the 4 wire attachments and removed the ddor latch assembly, and re-assembled with the new parts. Pretty easy job- the only unusual thing was that you need a torx screwdriver for the latch assembly.

I removed 6 screws to get to the door latch, then removed 2 screws to remove the broken latch assembly. Changed out 4 wires, reinstalled the 2 screws that attached the latch to the door,thenreinstall the 6 screws that assemble the door back together. Everything fit and works properly. Thanks guys, your service was great.

two screws, and pull unit out from under counter, turn on it's side. Two allen-head screws to remove motor retaining clip, unplug wires, and remove motor. Reassemble, using silicone grease on O-rings that seal motor. That's it.

Easy

I removed the screws on the inside of the dishwasher door to remove the front facade to get access to the door latch assembly, I think about 6 screws. Then I unscrewed the two hex screws that mounted the latch assembly to the door. I then had to un-hook the electrical wires (4 plugs, 2 on a side) from the assembly. I attached those same plugs to the new door latch, and mounted the assembly back on with the two screws, and tested the door to see if it closed, latched, and if the dish washer would run (since I unhooked and rehooked up the electrical wires). Finally I screwed the front facade back on and was done. It took about 5 minutes. I did get a small shock when I was removing the electrical plugs from the old assembly from touching the metal dish washer door and one of the plugs at same time.

I removed the screws from the inside of the door. There are also tiny screws you have to remove that holds the part onto the door. Then I was able to remove the part, unplug the power receptacles and install the new part. Very simple!!

After receiving my part in a timely manner, I removed the six screws holding the cover on the door. After making sure the appliance was unplugged, I removed the two star screws and removed the broken latch assembly. I disconnected the four electrical wires noting their placement. I connected the wires to the new latch assembly, screwed the assembly to the door, and replaced the cover on the door. That was one of the best quick-fix experiences I have ever had. Thanks PartSelect.com!!!!